Facade panels made of fiber cement boards are a practical and durable material for exterior finishing. Fiber cement panels for exterior home decoration

Everyone has long known that the facade of a house is the face of its owner. Therefore, everyone strives to make the appearance of their home impeccable. I am one of those people too. Having not only a private house, but also the dacha, I wanted to arrange each of them in its own way. Of course, the facades had to be different. Therefore, looking through the options, I decided that I would use fiber cement façade slabs. And below I will write why I chose this option for finishing the facade.

Façade finishing with fiber cement boards

What is the material famous for?

Fiber cement boards are environmentally friendly safe material, and their composition contains up to 90% cement. Thanks to this, they began to decorate not only high-rise buildings, but also private houses and cottages. These panels are distinguished by their high strength, which is achieved thanks to reinforcing fibers and mineral fillers. In addition, the combination of sand, cement and reinforcing fibers makes fiber cement panels not only strong, but also durable, but resistant to corrosion and rotting. And fire resistance makes them even more reliable. I want to say that among all the other facing materials for the house, it was fiber cement products that won my attention, thanks to the huge number positive properties and characteristics.

Facade made of fiber cement boards

Fiber cement facade slabs have the following properties:

1. Fire resistance - in addition to the fact that the panels will not ignite under the influence of fire, they will serve as an insurmountable barrier for it
2. Due to excellent tolerance of low and high temperatures, called heat resistant
3. Cement panels are resistant to chemical and biological influences
4. Not afraid aggressive environment and mechanical impact

In addition, I liked that fiber cement products are not afraid of open sun rays, and ultraviolet radiation does not affect them in any way. Facing slabs weigh half as much as porcelain stoneware, which means that the load on the house will be significantly less, and reliability and insulation will not suffer from this.

Textures of fiber cement boards

Important! A distinctive characteristic is the ability of the slabs to self-clean. When dirt gets on fiber cement products, it is destroyed and then washed away by rain or snow.

Having a large number of options for the facade, you can imitate the finish of granite or stone, because specifications maximally convey the colors and textures of the materials they imitate. Of course, installation of slabs is very simple; with a little experience and some skills, you can finish the facades yourself. However, if you are not confident in your abilities, then it is better to leave all the work to professionals; they will definitely not spoil the appearance of the house.

Fiber cement panels for facades

Along with its properties, fiber cement material has a number of advantages, which I highlighted when arranging my façade:

• When making tiles, autoclaving is carried out, and this serves as an obstacle to the formation of limescale deposits
• No special preparation of walls or their adjustment will be required. This type of façade cladding will hide all unevenness and cracks, along with stains and remnants of old paint.
• Fiber cement products are economical and at the same time their quality is no worse than other facade materials
• Installation work can be carried out at any time of the year
• This finishing protects the facade from various weather conditions that are unfavorable. The material is not afraid of UV rays, sudden temperature changes and exposure to microorganisms
• Any projects and design solutions can be done using fiber cement panels. There is a huge selection of textures and colors

Using fiber cement for OSB panels

Very often OSB boards are used for facades. It would be more correct to call them OSB, but using the transliteration OSB, with in English, everyone is used to calling them exactly OSB panels. The use of such materials is possible for various purposes, not only for the facade, but also for the floor or walls interior space Houses. This is a very light, but at the same time durable base, which has recently become applicable for the construction frame houses. However, in any case, OSB needs to be coated with something, and depending on the scope of application, the coating may be different.

Fiber cement panels - facade finishing

If we talk about the production of furniture or, for example, covering the floor in a house, then you can definitely paint the surface. But if we are talking about painting OSB, which is located on outdoors, for example if it is frame house, then it is better to use another coating that will adhere firmly to the slab and protect it from adverse conditions.
For exterior finishing frame house Fiber cement panels can be used from OSB. By the way, very often OSB panels are used to level the walls of a house and, of course, after that they need to be covered. Simply speaking, for the surface covered with OSB panels, you can use materials that are suitable for wooden board. Thanks to production technology OSB boards quite strong and smooth.

Fiber cement boards for exterior finishing Houses

Installation technology

Regardless of what type of fiber cement boards you choose, the installation technology will be quite simple and straightforward.

I will write the main stages of cladding the facade with fiber cement elements:

• The very first thing to do is preparatory work. I cleaned the walls of the old coating and identified irregularities
• Afterwards, all window sills and protruding objects must be removed, and damage must be removed.
• Next, I placed marks in the places where the brackets will be located. The pitch should be 60 centimeters vertically and 100 horizontally

Installation diagram of fiber cement boards

• Then we install the subsystem. I used metal profiles because I don't trust wooden ones. But this is a matter of your desire
• Before installing fiber cement products, it is necessary to install thermal insulation. You can use fiberglass and secure it using dowels with wide heads.
• Next, I secured the fiberboards with staples, but you can also use nails - it all depends on the thickness of the material. Do not forget that you need to buy slabs with a reserve. Up to 7% of the material used can be wasted during circumcision
• Between the plates you need to fix the strips that will separate them, then you will get even joints. Later they need to be sealed with sealant

Fiber cement boards will improve the facade of the house

Among the many finishing materials, intended for the facade of buildings, the so-called fiber cement panels stand out significantly - they are produced using modern nanotechnology, which makes it possible to make this material practically invulnerable to natural factors. It is this that we will deal with in this article, in which, together with the website, we will study fiber cement facade panels, identify advantages over other similar materials and learn how to install them.

Fiber cement facade panels photo

First, it is necessary to clarify the situation with the question of what this material is. It is made on the basis of cement with the addition of additives that lighten the weight and increase its strength. In addition, special microgranules have been added to the initial composition of this material, the task of which is to absorb and release water depending on the humidity outside - in some types of fiber cement panels the granules can be replaced with special ones internal channels to remove excess moisture. This type façade panels are covered protective layer both from the front and back.

Fiber cement facade panels: advantages and disadvantages

Now about the advantages that it has fiber cement siding. There are quite a lot of them.

• Firstly, it is strength and durability. Leading manufacturers of this material, subject to installation technology, provide a 50-year guarantee on their products. But their service life is not limited to this; with proper operation, they can last up to 100 years.
• Secondly, they are unpretentious to weather conditions - fiber cement panels for facades can be used at temperatures from -80˚С to +80˚С. At the same time, their quality does not suffer, and their dimensions always remain stable and do not depend on temperature and humidity.
• Thirdly, fire safety - in this regard, fiber cement panels are ahead of other ventilated facade systems - for example, they burn out in a matter of moments, and the widely used “ecobond” melts. In this regard, fiber cement practically does not react at all to high temperatures.

Fiber cement siding photo

• Fourthly, environmental friendliness - no chemical products are used in the manufacturing process of fiber panels. Moreover, this type of finishing material can even be used for interior decoration premises.
• Fifthly, a variety of colors and structures. Leading manufacturers of fiber cement panels include more than five hundred varieties of this material in their assortment - they are made to resemble bricks, natural stone, tree, etc. It is quite difficult to find such a natural material, the structure and color of which would not be repeated by manufacturers of fiber cement siding.
• Sixthly, this is a simple and easy-to-do-it-yourself installation, which we will look at a little later.

Fiber cement panels for facades photo

How to install fiber cement panels: requirements for the frame

Installation of fiber cement panels is carried out using the so-called hinged method - this material is used to create ventilated facades. As a rule, the panels are mounted on a frame made of special metal profile, the device of which has a number of requirements.

1. It must have a certain structure - two types of profiles are used to install the frame - the first of them are installed horizontally, and the second vertically. The latter are attached to horizontal profiles - fiber cement panels will be installed on them.

How to attach facade panels photo

2. Secure fastening frame to load-bearing walls building. For these purposes, special brackets are used, which are attached to the wall through a paranitic gasket, which reduces the impact of house settlement on the frame. These brackets are mounted in a certain order - their vertical installation step is 1000mm, and horizontally 600mm. This is due to the size and features of the panels.

3. Insulation of the house - it is done at the stage of assembling the frame, or rather, immediately after installing the brackets. V in this case Can various materials: Equally applicable to both foam and mineral wool or basalt slab. The insulation must be securely attached to the wall using plastic dowels with wide caps (popularly called “umbrellas”).

It is on this frame that fiber cement panels are installed.

Sequence of installation of fiber cement siding photo

Installing panels on a frame: how to secure them correctly

The installation of fiber cement boards, as well as the manufacture of a frame for them, has a number of features.

• Firstly, this is a basement flashing, which will prevent the foundation from getting wet - it is installed at a height of 50–100mm from the building.
• Secondly, these are clamps, whose task is to fasten the panels. The bottom row of clamps must be installed immediately above the ebb - they will securely fix the panels at the base of the house. Clamps are mounted on each vertical guide.
• Thirdly, this is a vertical seam strip, which will ensure the correct position of the plates relative to each other - it must be installed in the same way as the guides, maintaining a vertical level.

All these elements are securely screwed to the frame using metal screws with wide heads.

Installation of fiber cement panels photo

Well, then come the panels themselves. They seem to be put on the lower clamps, and their top is secured with the next row of these fasteners. Clamps not only serve to securely fasten fiber cement panels to the frame; their tasks also include creating an expansion joint.

An important stage of the installation of fiber panels is correct formation external corners - here the manufacturer provides two options for solving this problem. In the first case, the panels are connected without trimming, and in the second - with trimming at 45˚. In both cases, in the process of formation corner connections A special sealant and protective paint are used, supplied by the manufacturer along with the panels.

Clamps for fiber cement panels photo

The production of fiber cement panels involves their manufacture different thicknesses– depending on it, another installation method may be used. For thin panels, the design of which does not provide a groove for installing clamps, is typically fastened with self-tapping screws through the panel.

In such situations, special attention must be paid to the process of drilling this material - the holes should not be located at a distance closer than 50mm from the edge. Inner surface the holes must be coated with a protective primer, which is also supplied by the manufacturer along with the material. In the same way, without the use of clamps, slopes from fiber cement siding are installed.

Well, in conclusion, I want to say one thing - fiber cement facade panels are quite finicky to install. In addition, you will not receive a manufacturer’s warranty on the material if its installation was carried out in violation of technology, and such a warranty is at least 50 years. Therefore, you should think about this issue and entrust the installation of fiber panels to official representatives of the manufacturer.

Fiber cement boards are a finishing material of artificial etiology. Form of its production: slabs or siding. Facade panels are 90% cement, the rest is cellulose synthetic fibers, that is, fibers, as well as various mineral additional components. The outer layer of the slab is a weather-resistant coating. It can imitate stone and brickwork.

In the manufacture of this sheet material, these are substances that give the coating the following qualities: the ability to “breathe”, protection from moisture, and resistance to dampness.

Detailed specifications are offered in the following tables.

Physical data

Indicators of physical and mechanical qualities

When purchasing sheets for exterior cladding of a house, be sure to ensure that they comply with DIN EN 12467 and GOST 8747-88.

Advantages of facade panels made of fiber cement:

1. Excellent protection against aggressive factors (temperature changes, precipitation, mechanical influences).
2. Environmental Safety. The material does not harm either humans or the environment, because it contains no hazardous substances.
3. Ease of installation. It can be carried out in any weather.
4. Rich color palette, choice of textures and shapes.
5. Reasonable price panel.

Flaws:

1. If painting is necessary, costs increase for facades.
2. High level of moisture absorption (about 10%)
3. The appearance is inferior to many types of external finishes. Although this opinion is ambiguous. Facade fiberboard does not always inspire confidence among designers.

Decor

When studying the appearance, the fiber cement non-combustible panel is divided into the following categories:

1. Imitation of stone masonry. There are many options in this category. The criteria for distinguishing them are as follows: shape, parameters of the “stones,” color, degree of detail, texture specifics.
2. Imitation brickwork. White, yellow and red variants are often found here, and other colors are less common.
3. Imitation of painted wood. There is more to this category.
4. Fiber cement with stone chips. Their differences: colors, fraction parameters, presence of inclusions.
5. Products solid color and with a “plaster” texture.

Products of similar color - facade panels with marble chips. They are less often used to decorate private houses. Fiber cement facade is suitable for both office and multi-storey residential buildings.

Kinds

There is a wide size range in the types of panels. Products from Japanese manufacturers are usually classified into a different category of finishing materials. The length of the Japanese slabs is impressive, for example 182 and 303 cm. And the width is modest: 45.5 cm. Thickness range: 1.2 - 1.8 cm.

Products from Russian and European companies have different parameters (in cm), for example: 77 x 120, 30.6 x 159, 45.5 x 159.3, 119 x 156, 122 x 244, 120 x 150, 122 x 252, 300 x 150, 360 x 150. The interval of their thickness: 0.6 – 1.6 cm.

Japanese manufacturers often coat their products with a glass-ceramic layer. It turns out very powerful protection from external influences. Therefore, the prices of Japanese glass fiber reinforced concrete panels are several times higher than the prices domestic analogues. The Japanese are also making more extensive decorative options– about 500 decors. The warranty period for their products is up to 10 years.

Fiber-reinforced concrete slabs may differ in the type of joining edge. Some panels are equipped with clamp plates, while others are not. Panels with such plates have protrusions on the long sides. with clamps it has no visible fastening and looks more expensive.

Fiber cement panels and siding (FP and FS)

FS is wide boards decent length. Their appearance is similar to rare varieties of wood. To the touch FS also resembles exactly natural material. The FS parameters are usually set by the manufacturer himself. Today, two types of FS are widely used:

1. Flat board. It is mounted with an overlap. Perfectly imitates.
2. A board equipped with a chamfer - a special groove. Thanks to it, installation can take place end-to-end. This view is excellent.

FP are slabs rectangular shape. Usually they look like stone or brick. There are also smooth options for plaster. They look like a plastered wall. This is the facade made of fiber-reinforced concrete.

Differences between fiber-reinforced concrete panels and fiber cement panels

When solving this issue, one conclusion emerges - there are no differences. This is the name of the same material. It’s just that some manufacturers call their products fiber-reinforced concrete, while others call them fiber cement. In practice, these are the same material.

Manufacturers and prices

This is one of the most key issues today. Here, a lot is decided by the purchasing financial abilities and goals. Some people are not looking for special quality and may purchase cheaper versions. For some, quality is a priority criterion, and as a result, expensive Japanese or European options are purchased.

Japanese products come to Russia mainly from two manufacturers: KMEW and TM NICHIHA. They are listed as part of the Panasonic corporation. Their products have highest quality, and, logically, at the same prices.

Among Russian manufacturers, the leading positions are occupied by ROSPAN and LTM. However, there are many more modest companies that are trying to achieve Japanese quality in their products.

Buying fiber cement panels is a very responsible matter. Here it is important to choose high-quality, smoothly colored material and not overpay. It is useful to study the products of foreign and domestic manufacturers before purchasing. Foreign manufacturers are represented by the brands “Cembrit” and “Swisspearl”, the density of these boards is much higher than domestic ones. Some types of foreign fiber cement can even be fixed in a hidden way, onto the Keil bolt, in the same way as porcelain tiles are fastened without visible elements.

Painting fiber cement boards

When choosing paint for fiber cement boards, it is necessary to base it on the existing color scheme of the house, as well as the roof.

At self-painting For such slabs, it is important to comply with the following criteria:

1. There should be no defects on their front sides.
2. Do not fill cracks with putty.
3. After sanding, dust and dirt are removed from the slabs. Compressed air is used.
4. The boards must be completely dry.

Fiber panel painting technology

A diluted fluat fixative is used. To apply it to the front surface of the slab
use a roller or brush. The substance is absorbed in about 15-20 minutes. Next, the slabs are stored for a day in a room with parameters of +18-24 degrees and 50-60% (humidity).

Then the slabs are treated with a special impregnation on both sides. Drying follows. At 50-60C it lasts 1 hour. At 20C – 12 hours.

You need to tint the paint 2 hours before use.

The working tool is an air pistol. Requirements for it: clean and dry. Necessary parameters for work: pressure 3-4 atm, nozzle dimensions - 1.8 - 2.2 mm.

First apply one coat of paint. It dries up. Apply the next layer. The required wet film thickness is 80-120 microns. If necessary, after drying the final layer, sanding is done.

You can also work using the following technologies:

1. RP – “reduced pressure”.
2. HVLP – “high volume, reduced pressure.”
3. Combination of applications: air and airless.

Application without air is not permissible!

Drying the slab after painting

After priming, thorough drying follows: the slabs are kept at 18-24 C for 10-20 minutes, then
sent to the dryer. The conditions there are: 40-60C and 50-80% (humidity). Drying period – 2-4 hours.

After painting (colored paint is used), the slab is kept for 10-20 minutes, then again placed in the dryer under the same conditions. Only the drying period is 3-4 hours.

In practice, the final information on the drying period largely depends on the efficiency of the dryer itself. Complete polymerization occurs after 5-6 days. Before this time, installation of slabs cannot be done.

We suggest you read about installing fiber cement boards in a separate article.

The choice of finishing materials is surprising in variety. Manufacturers continue to develop this segment of the construction market, offering practical options exterior finishing for new, old and even dilapidated facades. The advent of fiber cement panels solved the problem of balance between safety, durability, simple installation and aesthetics.

What is fiber cement siding

Fiber cement panels are the latest building material used as a fast, safe way beautiful cladding residential buildings And public buildings. The variety of manufactured products provides a decent selection of panels that will not limit the implementation design idea. Palette of colors, textures with imitation under natural materials, matte or glossy surface, the ability to attach to any type of sheathing - this is what makes fiber cement panels for exterior home decoration so popular.

How are fiber cement panels made?

Fiber cement boards for facades are made on the basis of concrete and fiber:

• The first main component is high-quality grades with increased strength characteristics, which ensures the panels long term services.
• Fiber - the second component of the base - is a mixture of fiber and cellulose, which helps make concrete porous in order to reduce the weight of the panels and give the modern facing material flexibility, ductility, and resistance to deformation.

The process of creating fiber cement boards consists of four successive production stages. First, the extruder feeds the mixture, and a special machine rolls it out into a thin layer, layer by layer, to achieve required thickness. After this, the workpiece falls onto a conveyor belt, where the sheet is cut into slabs. The next stage is press processing, and the final stage involves applying decorative or protective coating.

What are the pros and cons of fiber cement facade panels?

Useful Features, which facade slabs for exterior finishing of a house made of fiber cement mixture have, significantly exceed the few shortcomings of the material. Technical specifications panels according to GOST 8747-88 classify these materials as frost-resistant, non-flammable, UV-resistant and durable materials.

The advantages of fiber cement panels for exterior home decoration include the following:

• high level protecting the facade from various negative factors (temperature changes, precipitation, mechanical influences);
• the possibility of creating an external ventilated facade (like a red one) or paired with insulation;
• health safety and environment due to the absence of harmful chemical components;
• simple installation that can be done in any weather;
• diversity color palette, textures, shapes.

Among the disadvantages of fiber cement boards for facades:

• increased painting costs;
• relatively high coefficient of moisture absorption (up to 10%).

Where to buy and how much do cladding panels for the facade of a house cost?

Reasonable approach to expenses for cladding external walls building involves choice quality material without overpayment. To buy fiber cement panels for the exterior of your home, you should get acquainted with the products of foreign and Russian manufacturers. The official website of the manufacturer will be a good guide, and bargain purchase It’s easy to do both in a large building materials store and in cooperation with intermediary companies.

Exterior finishing of the house with fiber cement panels

Installation of slabs made of fiber cement mixture is carried out on the basis of ventilated facade technology. Fiber cement panels for exterior decoration of houses are mounted using a hinged method, and to increase the level of thermal insulation under external cladding insulation can be installed. Before installation, the surface of the building wall must be prepared (removal of plaster, old cladding, hanging elements), then the subsystems are installed, after which the slabs are fastened, maintaining the level.

For exterior finishing, fiber cement panels of different thicknesses can be used; even for a novice builder, this may not be a problem if self-tapping screws or metal brackets (galvanized) are used. Installation is carried out from above: so as not to damage facing material, you should retreat 20 mm from the edge, treat the seams with primer and sealant, and coat the metal fasteners with water-repellent paint.

How to choose the right fiber cement boards

To Wall panels for exterior decoration of the house have served for a long time, it is necessary to do right choice. Criteria that must be taken into account at the selection stage include the quality of products from trusted manufacturers, warranty conditions, level of moisture resistance, assortment and the presence of special coating. An important factor The weight of the panels is considered, which differs for each manufacturer, because the load on the walls and foundation of the house increases. Other important detail– the presence of clamps (fastenings) that will help completely hide the horizontal seam.

Photo: exterior decoration of the house with fiber cement siding

Fiber cement panels for exterior decoration of houses are a guarantee of beautiful and durable design of the exterior of the building facade in a certain style. Thus, fiber cement siding Latonit will do an excellent job of protecting walls from any unfavorable vagaries of nature, while it is practical and durable. This finish is a worthy alternative to wood, stone, and brick. External cladding buildings with fiber cement panels are at the peak of their popularity today.

Video: how cladding panels are installed for exterior finishing

Today's market building materials literally overflowing with various finishing options for the facade of the house. Among them in great demand fiber cement slabs are used. To obtain them they use modern technologies. It's completely environmentally friendly pure material, which does not emit harmful components during operation. Fiber cement boards are structural element in a ventilated device curtain façade in houses where capital and frame walls are provided.

a brief description of

Fiber cement boards are a modern finishing material that is used in the construction of facades. In the manufacture of boards, components such as cellulose fibers and mineral fillers are used.

The structure of the finishing material is represented by the following layers:

• fiber cement sheet;
• water-repellent layer;
• decorative layer.

The picture shows where the fiber cement board is attached

As for the dimensions, fiber cement boards are made in the following sizes:

• length 1200-3600 mm,
• width – from 445 to 1500 mm,
• thickness 4-18 mm.

Here's how to insulate a facade brick house from the inside, and which materials are the best for these works, indicated

In the manufacture of such products, a pressing method with further heat treatment is used. Thus, the resulting material is characterized by high strength, flexibility and uniform structure.

Boards made from fiber cement have a large number of positive properties, thanks to which they compare favorably with other finishing materials.

The main advantages of fiber cement boards include:

• resistance to weather influences;
• low thermal conductivity;
• excellent sound insulation;
• breathability.

Here's how to insulate the facade wooden house outside, and what materials should be used first are indicated

On video - fiber cement boards for facades:

The finishing process is not particularly complicated, and the material itself does not require careful maintenance during operation. Strength is many times greater than that of other finishing materials. Thus, fiber cement panels do not break under the influence of mechanical loads. The service life of the finish is more than 50 years.

Use slabs for finishing multi-storey buildings, shops, supermarkets, train stations and private houses. For fire-resistant fiber cement boards, the scope of application is expanding, so it can be used for cladding baths, saunas, stoves and fireplaces. When combined of this material with other decorative coatings it is possible to obtain an incredibly stylish and original exterior. Since the slabs are quite flexible, they can be used when cladding houses of various configurations. A wide range of color range and textures allows you to implement any design idea into reality.

But how the facade is finished with foam plastic and plaster, and how such work is carried out, can be seen in this

Installation

The process of arranging a facade using fiber cement boards begins with the installation of the frame. For these purposes, metal brackets with a paronite gasket are attached to the load-bearing wall using dowels. A vertical distance must be maintained between them, which will be equal to the dimensions of the heat insulation sheet. But this value should not be more than 60 cm. Fastening horizontal profiles the frame to the metal brackets is done using rivets or self-tapping screws.

Here's a video of how fiber cement boards are installed on a façade:

Fiber cement boards are made with or without grooves, of different thicknesses, which determine the method of installation of the material. If installation is carried out with grooves, then this must be done using clamps, and thin elements to the frame profiles vertically are carried out with sealing tape and self-tapping screws.

In this case, the vertical spacing between fasteners should not be more than 40 cm. In the panel fastening area, drill a hole at a distance of at least 5 cm to the edge of the material.

Vertical and horizontal connecting gaps between fiber cement boards should not exceed 2 mm. If decorative façade ebb is used in horizontal connections, the gap between the panels will be 10 mm. If a corner decorative profile is used in vertical joints, then the gap from the edge of the finishing material to the corner will be 2 mm.

You may also be interested in information about how

Manufacturers and prices per m2

Today the range of fiber cement boards is so wide that it is not always so easy to make a choice. You can trust the following manufacturers:

• Latonite. This is a domestic manufacturer that produces fiber cement boards according to European standards. Every year the company produces various options slabs that differ in color and texture. You can purchase products at a price of 300 rubles per m2. It is also worth paying attention to how

  

  From the manufacturer Latonit

• Minerite. This company produces fiber cement in Finland. Due to high thermal insulation properties material can be used for finishing both private and multi-storey buildings. You can buy products at a price of 1100-12000 rubles per m2. But you can see how the facade of a private house is decorated with polyvinyl chloride panels

  

  From the manufacturer Minerit

• Nothing. This is a Japanese manufacturer that uses special technology in the production of slabs. Thus, the slabs do not shrink after installation. This is a feature of the brand in question. You can buy products at a price of 2400 -3100 rubles per m2. It will also be interesting to learn more about what other

  

  From the manufacturer Nichikha

• Flamma. This is another domestic manufacturer that produces fiber cement boards that are highly fire-resistant. This material is used in the construction of baths, saunas and hot stoves. The cost of production is 1,700 rubles per m2. Here's how to apply it warm plaster for the facade, you can read in this

  

  From the manufacturer Flamma

• Kmew. This Japanese manufacturer has been producing fiber cement boards for 40 years. Thanks to such wide experience, the products produced are improved. You can buy it at a price of 1200-1600 rubles per m2.
  
• Kraspan. This company is engaged in the production of finishing materials, including fiber cement boards. This material is available in a wide range of colors and textures. You can purchase products at a price of 1300 -1600 rubles per m2.

  

  From the manufacturer Kraspan

• Rospan. This is a Russian brand that produces fiber cement boards that meet the standards. The range includes a wide selection of finishing materials to create a stylish and modern design. You can purchase products at a price of 1500 -2100 rubles per m2.

  

  From the manufacturer Rospan

• Cembrit. This company is located in Denmark. The fiber cement board produced by this brand meets all standards, because the company has a strict quality policy. You can buy slabs at a price of 2400 -2600 rubles per m2.

  

  From the manufacturer Cembrit

• . The peculiarity of fiber cement boards produced under this brand is that they have an acrylate coating. It can take any color according to the customer's wishes. The produced boards are environmentally friendly, durable and reliable. You can buy them at a price of 1700 -2300 rubles per m2. You should also pay attention to what it looks like

  

  From the manufacturer LTM Sinom

Fiber cement board for finishing facades is a material unique in its qualities. It is environmentally friendly, durable and resistant to various weather conditions. The slab can be used for cladding both private houses and multi-storey structures. With such finishing, any building will not only be protected from cold, moisture and other weather conditions, but will also acquire a pleasant appearance.