Finishing panels for the facade of a house with a stone look. Stone-look facade panels. Vinyl siding prices

Once faced with the need to decorate the facade own home, and having at the same time an extremely limited budget, I decided to consult with friends who had already gone through this. Imagine my surprise when three out of five respondents recommended one well-known resource.

From the very beginning I considered it as finishing material, only facade siding, it looks, of course, banal, but I didn’t count on more with my finances.

I went to see it, and to be honest, I was amazed, but first things first.

Types of facade panels

It turns out that siding is not only straight stripes on the walls of a house, but also a whole catalog of various imitations.

Tree.
Wild stone.
Brick.
Granite.
Marble.

I especially liked the stone-look plastic panels. I, as a non-specialist, did not even immediately determine that this was an imitation.

Cladding a house with natural stone has always been a pipe dream, but its price sometimes exceeded the cost of the house itself. Having walked around the expanses of sites, I discovered several very important points, after which there was no doubt about the choice.

Appearance. It is possible to distinguish façade panels from natural stone only upon closer examination.
Acceptable price. Compared to other types of finishing, stone-look facade panels turned out to be several times cheaper.
Easy installation. After looking at the installation instructions on the website, I realized that I could do it myself.
Durability. The production of facade panels from hard vinyl implies their service life of at least 30 years. When used in the harshest climatic conditions.

I found a calculator at dom sidinga, did some simple calculations, and it turned out that final cost even lower than what I originally planned. And it’s not just the cheapness of the material, the price was significantly affected by the fact that I will be doing the installation myself, and the fact that it turns out that I don’t have to put insulation under the façade panels!!!

There are two types of facade panels:

Single layer.
Multilayer.

The first option, of course, is cheaper, but it requires the installation of insulation, and the production of multilayer facade panels implies the presence of a layer of polyurethane, which acts as heat and sound insulation.

Having compared all the pros and cons, I highlighted the beneficial advantages of multilayer panels:

When finishing with your own hands, they do not require laying additional layers of heat, hydro and sound insulation;
Installation is possible at any time of the year and at any temperature;
Completely insensitive to moisture;
More high density façade panels almost completely eliminate temperature deformation;
The polyurethane layer can withstand a large number of freezing and defrosting cycles.

In a word, there is no doubt left. I refused the services of builders, since I still decided to do everything myself, so I simply ordered delivery of everything I needed on the Internet, and started work the very next day.

Features of facade panels and installation

I was pleasantly surprised by the fact that to install plastic facade panels with your own hands, you do not need any special tool, almost everyone has everything they need at home:

Roulette
Hacksaw, preferably with small tooth for cutting siding
Drill with impact mechanism. And if the house is wooden, then without it
Screwdriver. (you can get by with a drill)
Building level

First of all, it is necessary to treat the walls with soil, which will protect them from fungus. Next, we make a sheathing that will hold the siding on. At first, in order to save money, I wanted to put it on the sheathing wooden beam, but specialists from the site explained that the difference in price between timber and metal profile practically none, since the tree requires additional processing impregnations.

First, using a drill, we attach the holders that will fix the profile to the wall; it is important that they are positioned strictly along the vertical line over the entire height.

Advice: at the stage of lathing production, you need to check the level as often as possible, since crookedly installed guides will create a lot of problems during finishing.

The distance between the guide profiles should be 30-50 cm, and the step between the holders should be up to 1 m.

The guides can be mounted at a very minimal distance from the wall, since multilayer facade panels do not require insulation; the distance is only necessary for free air flow.

The next stage of production is the actual installation of the façade panels. Even before I decided to do the finishing of the facade with my own hands, I was convinced that the panels were attached first, and then the decorative plastic corners and everything else were attached to them. But after reading the instructions on dom sidinga, I learned that you need to start from the corners and joints of the panels.

Having secured the corner panels with self-tapping screws, we measure the distance between them; if it is more than 3.4 m, then at this distance you need to install an H profile, which connects the two panels in length.

Sometimes, for greater aesthetics of appearance, the H profile is placed exactly in the middle of the house. In this case, you will have to cut each panel to length, and the consumption will increase slightly, but the vertical line will run in the center and will fit well into the overall look.

If everything is ready, we mount the starting panel, it is located at the very bottom and all the rest of the finishing will come from it. In cases where the foundation does not protrude beyond the walls, finishing is carried out from the ground itself. This is not recommended; there is a special siding for the plinth that has more durable characteristics.

Important: the starting panel must be clearly level, since a misalignment of just a few millimeters will greatly affect the finishing stage.

After the starting façade panel has been installed, the simplest step remains - installing the siding. To do this, take the panel and, bringing its edges into the corner and H profile, engage the lock with the starting bar, then fasten the panel with a self-tapping screw into a special oval hole so that the cap is in the middle of the oval.

Important: when tightening the screw, you need to make sure that it does not press the panel. The siding should seem to hang on a self-tapping screw.

In this way, all siding segments are assembled and fixed under the roof with a finishing panel.

The finishing of the house with facade panels is completed, now the room will become much warmer, and the house will take on a new face.

Conclusion

Facade panels for a private house under the stone

By the way, it took me two days to finish the entire house with my own hands, and this taking into account the fact that I had never dealt with facade panels before. Of course, many will say that a natural stone Nothing compares, and I probably agree with that. But often, the question of the price of finishing materials plays a key role in their selection.

Moreover, not everyone can do the finishing with natural stone with their own hands; it requires special skills and a set of tools. There are no such problems with siding, and this puts it a step above its competitors.

Manufacturers offer a large number of materials so that each developer can cladding the façade of a house to their liking. Of course, stone finishing is one of the most ideal options, but also one of the most expensive. An alternative is panels with an imitation of stone texture, while the material retains all the qualities and practicality, and in some ways even surpasses natural material.

Features of the material

Facade panels imitating stone are divided into two types:

Having a homogeneous structure, made of PVC and modifications.
Combined elements with a multilayer structure, equipped with an insulating layer.

Thanks to the presence of expanded polystyrene, combined type profiles have increased thermal insulation qualities and also protect the house well from noise from the street. Sometimes there are foam sheets used as insulation, however, like polystyrene foam, foam is installed without the use of glue by heating.

The peculiarity of the product is its resistance to temperature phenomena and imperviousness to water flows. Moreover, even sharp changes in thermometer readings per day do not affect the strength of the profile in any way; there is no deformation, fragility or other unpleasant qualities. Having a low score linear expansion, the panels eliminate the appearance of such factors as: peeling, change in stable shape. Well, wide color and the lineup products allows you to select profiles of the desired shade and texture.

Material advantages

The main advantage of the material is its price. It is much lower than natural or fake diamond. Installation work They are easy to do with your own hands, and at the same time, covering the house with panels does not take much time. The all-season nature of the processes is also a plus: profiles are attached even in snow or rain, of course, if it is a glue-free technology, otherwise dry and warm weather. Also:

There is no large dust when working with panels;
The profiles are light in weight, unlike natural or artificial stone, which means that the weight of the finishing will not have to be taken into account in the project and a strong foundation will not be laid;
During the installation process there is practically no need to use adhesive solutions;
The presence of corner fasteners reduces the time of drawing corners;
The large area of the panels allows you to quickly cope with façade cladding of any size;
The strength qualities of the panels, resistance to water and snow will serve any façade well;
The material from which the building is built does not matter - installation is carried out on buildings of any type and number of storeys.

According to their varieties, profiles are divided into two types:

Decorative. They are used for covering both the walls of the house and the basement. The variety of palettes and textures will help you choose perfect solution for facing works.

Important! If you choose panels that are fastened to each other, you will not need to install a frame.

Insulated ones allow you to fulfill two conditions at once: decorate the facade and lay additional insulation. At the same time, significant savings on materials are achieved, heat loss is reduced and the risk of mold and mildew formation is minimized.

Thus, stone panels are good substitute natural or artificial material. Service life from 25 years, high performance strength, no need professional styling, efficiency of work, minimal load on the foundation and a huge selection color solutions– in many respects facing material superior to natural and artificial stone. Considering that the price of profiles is several times lower, it becomes clear that cladding a house with stone panels is profitable and practical solution problems of aesthetics of any structure.

Step-by-step instructions for installing profiles

It is worth immediately noting that the cladding of the plinth and the facade have the same technology, so there is no particular difference in the process

It is worth immediately noting that the cladding of the plinth and the facade have the same technology, so there is no particular difference in the process. The main thing to remember is that to decorate the basement of a house with plastic panels, select products made specifically for basements! Such profiles are slightly thicker and therefore stronger. At the same time, the panels for the ground floor are better able to withstand mechanical stress, and if desired, the developer can completely decorate the façade of the building with just such a material. However, wall profiles have big sizes, rather than products for the ground floor.

What to do:

Determine the amount of material for finishing the outside. To do this, you need to know the profile area and the area of the house facade minus windows and doors. You will have to take into account overlaps, cuts and add another 10% to the resulting amount; if the panel has a complex texture and configuration, then add the entire 15% to the resulting amount. The quantity is also calculated starting bar, for this, the sum of the perimeter of the building is divided by 3 meters - standard length planks.
You will need external corners according to the height of the cladding, the number of which is also calculated by the sum of all angles and dividing the result by 0.45 m (height of the standard element) plus 5%.
An internal J-profile, the length of which is 3 meters, will come in handy. The quantity is calculated as needed, for example, if you plan to use profiles for finishing a doorway, then there will be more.
It would also be a good idea to check fasteners and tools before starting work.
The installation process begins from the corner, a starting strip is attached at a distance of 10 cm at the very bottom of the wall, the horizontal and vertical level is measured, the mounting step of the strip is 30 cm.
Facing the foundation involves first fastening the first outer corner, then checking the lower level for the evenness of the starting strip, and fastening it.
The panel is inserted into the strip, pushed into the groove so that the gap from the outer corner is no more than 3 mm, the lock of the strip is latched, and the edge of the panel entering the groove is cut at a right angle.

Important! You should not veneer two corners at once; all work is carried out in stages. The panels can and should be cut, but the first and last profiles must be at least 30 cm wide, but the remaining trim is inserted just as the first or last panel.

The last profile is attached to the left with one fastener, the right side is bent, the last element is mounted in the groove, both panels are bent and joined, secured.
After the first row is completed, each subsequent row is performed by installing the upper profile into the lower one. And to connect with the previous one, it moves slightly to the left.

Important! In the place where the ground floor ends, a curb is mounted on the profile, only then attached to wall panel. And façade outer profile inserted into the mounted border.

Don't forget about the additional facing decor. These could be visors, shutters, and other elements. Installation is carried out on top of the panels to the sheathing. Drilled out required quantity holes, the diameter of which is larger than the diameter of the fasteners, the trim is installed. After this, the work process can be considered complete.

As you can see, cladding a house with stone panels is much easier than laying a wall made of natural or artificial material. Among other things, you don’t have to resort to the help of professionals, lift weights and spend a lot of money. Well, the result will exceed any of your expectations - it turns out very beautiful stone house stable form, even if it is an old wooden mansion that has stood for decades.

Siding is not just a boring and monotonous exterior facade decoration. There are many varieties of this material for all occasions. If you are a fan of permanent buildings, then pay attention to the stone-look facade panels, which will give the house the new kind. The material imitates large boulders, flat, rubble and other types of stone. Facade panels for exterior finishing They will completely transform the simplest house into stone, and in addition it will become warmer.

Finishing the facade of the house with stone panels

Blocks for exterior finishing perform not only an aesthetic function. The facade decoration is reliable protection home from negative impacts. Installing slabs on the walls of a building allows you to extend its service life and completely renew the façade without significant costs. Siding is a lightweight material that does not place significant load on the building. Installation of the panels is simple - their installation does not require highly qualified workers, which means the cost of the work will be low.

Stone façade finishing options

Cladding a house with stone-like panels is done in one or several shades of the panels. By using multiple colors and textures, you can highlight multiple design elements. These could be windows, corners, basement.

It is customary to install darker and larger elements on the base. Lighter blocks are used for walls.

The finishing of a private house is made with stone-like facade panels in two shades

Manufacturers produce a large number of stone panels designed to various conditions operation.

Types of panels

Stone siding differs in several ways:

material;

the presence or absence of insulation;

fixation method.

The following materials are used for siding:

fiber cement.

The dark shades of the panels highlight well bright windows building

Metal siding

Metal panels are made by stamping. Galvanized steel blocks are coated with polymer protective composition, a layer of decor that reproduces the surface of the stone. By applying several layers of coating, the blocks become thicker and heavier. But this increases the strength of the material. Metal siding costs more than vinyl.

The panels may have different patterns, for example, the corners are “lined” with a geometric pattern

On our website you can find contacts construction companies who offer the service of finishing and insulating houses. You can communicate directly with representatives by visiting the “Low-Rise Country” exhibition of houses.

Vinyl panels

Panels made of plastic (polyvinyl chloride), known as lining, serve indoors without problems. This material is not suitable for finishing the facade. Manufacturers have created a special composition for external finishing works. It is characterized by increased strength, resistance to temperature and mechanical damage.

The main advantage of vinyl blocks is their lightness. They do not significantly increase the weight of the building. The material is plastic, so vinyl siding reproduces as much as possible appearance natural stone.

The disadvantage is considered to be its fragility. Vinyl is inferior to metal in its resistance to temperature changes and is easily damaged during installation. It is less resistant to mechanical damage during operation. Under influence high temperature it can increase in size. This subtlety should be taken into account when calculating the number of finishing slabs.

The texture of the panels imitates granite stone

Acrylic

By technical specifications acrylic siding is similar to vinyl. It has the same advantages as vinyl, but is more resistant to high and low temperatures. The material is neutral to chemical influences.

Stone effect acrylic panels for exterior finishing The cost of facades is slightly higher than their vinyl counterparts.

Volumetric facade panels imitating rocky stones

Fiber cement

A relatively new type of finishing is fiber cement siding. Of the listed types of panels, this is the heaviest. The weight of the blocks is 15 kg, thickness 10 mm. They have increased strength and durability.

The cost of fiber cement siding is much higher than other types. For finishing facades, consumers prefer lighter and cheaper types of slabs.

The color and texture of the finish reproduces granite, rocky stone, rubble or burnt stone. By using modern technologies can be reproduced natural stone with maximum accuracy. The similarity of siding is not only visual, but also qualitative.

Imitation rubble stone

Some types of blocks are not only decorative - they also inside they have insulation on them, so that insulation work can be combined with façade decoration.

If the building is located in an area with a warm climate, finishing the house with stone-look panels made of fiber cement does not require additional insulation of the walls. If the house is located in a cold climate, additional insulation of the building will be required.

Therefore, there is no point in buying siding with insulation in cold regions. The installation of blocks with a warm layer is no different from the installation of conventional panels. The cost of warm siding is higher than the cost of simple siding.

Each block is equipped with locks. With their help, fragments are held together. Fixation is carried out by snapping the locks.

Advantages and disadvantages of stone-look facade panels

Stone siding has a number of positive qualities:

long service life (50 years);

resistant to weather factors (wind, high and low temperatures, high humidity, impact sun rays);

not subject to corrosion;

universal – suitable for installation anywhere – on walls, plinth;

easy to install;

there is a large assortment on the market;

Facade panels imitating burnt stone

has low cost;

does not require maintenance;

has low weight (the load on the surface of façade panels imitating stone is 3-5 kg/m², natural stone – 53 kg/m², brick – 34 kg/m²);

resists insect damage and fungal infections.

Stone panels for external cladding the façade is inferior natural material in strength and durability, but not significantly. Against the backdrop of a large number of advantages, this disadvantage pales.

Video description

Watch the video to see what a house clad in stone panels looks like:

Stone plinth panels

The base (literally a shoe with a wooden sole) is a footing located on the foundation of a building. The load on this part of the buildings is greatest, so increased strength requirements are put forward for the base itself and the finishing materials.

The industry produces special plinth slabs taking into account the installation location. These are blocks made of stronger material with increased resistance to damage, temperature changes, moisture, wind, and ultraviolet radiation. Fiber cement siding ideal for plinth installation.

Often basement part houses are decorated with contrasting plates. Installing slabs on the plinth gives the building a more beautiful appearance.

This is exactly the decoration of the facade of the house with stone panels in the photo below:

Using siding that is darker than the base tone has become a popular home decorating element. Plinth blocks have a larger texture. This makes the lines of the house more expressive.

Step-by-step installation

For self-installation Sandwich panels should be prepared:

screwdriver;
centimeter;

hacksaw/grinder;

pencil/marker/chalk.

Before installation, the walls should be prepared. Residues are removed from them cement mortar, moisture leaks, metal elements. The surface is processed special composition, preventing the appearance of fungi and insects. After the solution has dried, begin installing the blocks.

Installation of the slabs is carried out on the prepared sheathing. If it is planned to lay insulation, heat-insulating blocks are installed first.

Step-by-step installation of stone siding.

The sheathing is installed on the wall. For this they use wooden blocks or metal slats. The planks are arranged in increments of 30 - 40 cm. They not only serve as support for the blocks, but also help to ventilate the walls.

Several types of profiles are used in the lathing

The starting bar is set. It is verified by level and the rest of the blocks are oriented according to it.

Corner panels and window panels are installed. Blocks are installed around doorways.

The following panels are carefully fastened to the corner blocks. The locks should be latched with a smooth movement so as not to break the structure.

Fixation with self-tapping screws is carried out with a small allowance. The cap is not screwed into the sheathing all the way, leaving 1-2 mm.

Each next row of panels is leveled. Sandwich panels should be installed from left to right.

First, the blocks are installed on a flat surface. After installing all the panels, the corner parts are secured. They snap easily onto the mounting profile.

Main condition quality installation sandwich panels - neatness. German Holzplast Wandstein panels have proven themselves well. Special attention require plinth blocks.

Video description

For an example of installation of Holzplast panels, see the video:

When calculating the number of panels, add 10 - 15% to the resulting number. This must be done, since the blocks have to be trimmed during installation.

Before installing the sheathing, you should first make markings in increments of 30 - 40 cm. After the position of the beams has been accurately determined, they are installed on the wall. The correct installation of the planks is checked using a horizontal and vertical level.

The screws are screwed into the center of the holes.

After installing the starting panel, pull the thread from the panel to the opposite corner. The correct tension is checked with a level. All lower blocks are installed according to this guideline.

The installation of basement blocks is completed by installing a drainage system. It is placed on the upper horizontal surface of the base. Metal elements are used for this.

Where is the best place to buy panels?

Manufacturers produce sandwich panels designed for the various financial capabilities of the end buyer. In Moscow, the cost of slabs starts from about 900 rubles per m². By purchasing façade slabs from certified manufacturers, we must remember that, unlike counterfeits, the price of the material is also affected by the rental of premises, the number of intermediaries and the wages of store employees. But in return you get quality products that come with a guarantee.

In addition, many manufacturers are beginning to master the sale of stone-look facades in online stores, which allows customers to save money and time.

Facade finishing with panels

from 680 rub./m2

Finishing facades with plaster

from 350 rub./m2

Finishing facades with artificial stone

from 1250 rub./m2

We offer finishing of the facade of a house with panels at a cost of 680 rubles/m2 (10.2014). Our specialists select best materials for external cladding of a wide variety of objects. You quickly get a beautiful, warm and durable facade. Call, find out current prices and order turnkey finishing!

Paneling

Finishing work

Our specialists inspect the facade and dismantle elements that interfere with the work.
Craftsmen prepare the base for finishing: remove loose coatings, remnants of paint or other old materials. Cracks and damaged areas are repaired.
The surfaces prepared in this way are treated with a primer, which protects the walls from fungus and strengthens the base of the facade.

Note! We attach the panels directly to prepared walls or installed sheathing. The frame is made of metal or wood. In the example below, the walls were level, so our specialists attached the panels directly to the base of the facade.

Installation work begins with marking out the horizon line along the perimeter of the building.
The base profile is attached using this marking.
Installation begins from the corner of the house. For this, craftsmen use corner elements. In their absence, ordinary panels are used. To do this, carefully cut the edge of the element at an angle of 45 degrees. This joint looks invisible.
We fasten the panels using kits for quick installation on brick foundations. You must first drill mounting holes in the panels.

Drilling holes in the façade panel and installing it

We also use for installation of panels adhesive mixtures and polyurethane foam.
After installing the first row, specialists perform work in the same sequence. The new element is installed so as to carefully align it with the fixed panel. We monitor the quality of insulation joining and carry out additional fasteners panels using dowels.
During the cladding process, our specialists process the panel joints polyurethane foam. This ensures a tight connection. After completing the installation of all facade panels, the joints are rubbed with a special frost-resistant mixture.

Execution of work

Tips from the experts: benefits of using panels with clinker tiles

You save on wages for specialists, because at the same time as the cladding work is carried out, the facade is insulated.
When installing panels on the frame, craftsmen equip a ventilated façade - the most effective solution V modern finishing buildings.
Work is carried out in any weather conditions and sub-zero temperatures.
You get a durable façade that requires no maintenance. The surfaces of the clinker material are resistant to ultraviolet radiation.
No reinforcement of the foundation is required, while the low weight of the façade panels creates minimal additional loads on the structure.

We use all types of modern facade panels, for example, Döcke products are very popular.

Summary

Choose best quality from professional performers. We guarantee years of trouble-free operation of the new façade. Call, find out prices and order finishing the facade of your house with panels!

Many manufacturers offer a wide selection of materials for decorating building facades. Most in an original way To achieve the unique appearance of a building is to create hinged ventilated facades. This technology is distinguished not only by its variability color range panels, but also by shape, texture and even the name of materials.

Panels made of polymers (plastic) are widely used.

Advantages

Plastic panels have whole line undeniable advantages Compared to other materials intended for finishing facades and even in front of metal panels:

Low weight of the structure;
Durability of the material;
Low price of material and installation work;
Ease of maintenance and repair;
Large assortment of types and shapes.

In our country, stone was considered a traditional finishing material, which is why the line plastic panels, imitating a stone surface, is the most extensive both in texture and color.

Types of plastic panels under stone

The most popular in the finishing materials market are plastic panels that imitate hewn, rubble or natural stone. . At the same time, manufacturers provide a full line of necessary bends, corners and strips of a given texture and color.

It is especially worth noting that different panel manufacturers use different sheet sizes, so it is advisable to purchase plastic panels for the base and walls from the same manufacturer. Mounting and fastening systems are practically the same different manufacturers. All panels are mounted sequentially from the starting strip, while the next panel is inserted into the previous one with grooves and fixed.

Manufacturers

There are a huge number of offers for the sale of plastic panels on the finishing materials market, but many of the selling companies are resellers, not manufacturers. The main manufacturers of plastic facade panels are: Nailite, Novik, Docke, FineBer, Holzplast, Vox and Alta profile.

U various manufacturers Not only the price of the finishing material varies, but also parameters such as color scheme, panel size, and quality of raw materials.

The Nailite company is widely represented in our market. One of the main reasons for this spread is extensive experience in creating facade panels. The company was founded in 1978 in the USA and has been importing its products to different countries peace.

The main series are: rubble stone (from simple to premium class), cedar, natural stone and ashlar. Moreover, the panels of each series can be made in several versions (usually two or three types) of colors.

Glacier White

Brown

The dimensions of the sheets (useful length) vary from 22.86x183.83 cm to 45.7x102.2 cm, while it should be taken into account that the total length of the sheet is slightly longer due to the fastening elements hidden during installation.

Prices from Nailite official representatives range from 509 rubles per panel.

The main dealers in Russia are the following companies: Euromet, TOP-HOUSE, Westmet, TechnoNikol.

The Novik company is a Canadian manufacturer of plastic panels, but its emphasis is on a large line of boards made under brickwork, although there are also panels that imitate hewn, natural stone and cedar.

The size of the panels (usable length) varies from 101x45 cm to 80x60 cm. Each model range has its own special standard sizes, while minimum price for one panel will be from 464 rubles and above.

The main dealers in Russia are the following companies: MirKrovli, Grotesk, Megastroy, etc.

The Docke company is a German manufacturer of plastic panels. The main series are: brick and stone (natural and hewn). A special feature of this company is the expanded palette of panel colors. There are from five to ten varieties of panel design colors, although many manufacturers limit themselves to two or three colors.

Zemlyanoy

Brick

Wheat

Cherry

Dark walnut

Amber

The useful area of the panels varies from 0.42 to 0.45 m2. At the same time, do not forget that many famous manufacturers provide the service free estimate required quantity materials and components. Some are limited to special calculation calculators presented on the company’s website, and some companies carry out a surveyor’s visit to the site. But a specialist visit is not always possible due to the distance from the representative office.

The minimum price for one plastic panel is 479 rubles. Many prices are valid for Moscow and the Moscow region. Prices in other regions must be confirmed with local offices and dealers.

In order to find out the location of the nearest Docke dealer, just visit the company’s official website, where more than a thousand different representative offices, intermediary companies and stores are represented.

Learn more about the quality and types of Docke panels.

The FineBer company presents a large number of series of facade plastic panels on the market: stone, wild stone, large stone, natural stone, brick, facing brick, rock, slate and Britt facing stone. The design colors for each series can be from three to six. Smallest area The “Natural Stone” series has coatings.

Zemlyanoy

Large white stone

Slate beige

Large gray stone

Facing brick ceramic

Gray-green stone

The FineBer company has a wide network of representative offices throughout Russian Federation. Prices and delivery times for the company's products vary by region. Full list representative offices are presented on the official website of the FineBer company.

Read why FineBer façade panels are among the best.

Holzplast

The Holzplast company relatively recently entered the Russian market. It started its activities in 2005.

The company produces plastic panels in six different series according to texture: brick, rubble, dolomite, parphyry, chipped and tuff. The company's product range includes 14 panel colors, but some series are available in only three colors, for example, dolomite in beige, gray and white.

The dimensions of the slabs of this company are unified among themselves and amount to 79.5 cm x 59.5 cm.

The Holzplast company has about 520 representative offices throughout Russia, only in Moscow and 150 official sales points in the region.

The Vox company offers two series of plastic panels: brick or stone. Moreover, only in one standard size for each type: 109.5x44.6 for stone-look panels and 111.3x46.7 for brick-look panels.

Vox has recently entered the market facade systems and its dealer network is not as extensive as that of the famous giants Docke, Nailite or Novik. But at the same time, today its representatives cover the main big cities Russian Federation.

Find out why Vox siding is praised.

Alta profile

The Russian company Alta-profile has been active in the façade systems market since 2007. A relatively large number of color series for the design of plastic panels allows it to compete adequately with more famous manufacturers.

New products from this company were the panels of the “Canyon” series, which almost immediately began to be produced in five color categories: Colorado, Montana, Nevada, Arizona and Kansas.

What you need to know before purchasing.

Moreover, one of the lowest prices for a panel is 415 rubles.

Technology for installing plastic panels under stone

Installation of panels can be divided into 3 stages:

Preliminary surface preparation;
Frame structure;
Installation of panels.

Installation of the panels begins with the installation of the starting and finishing profile, as well as guide profiles. The installation of the panels themselves is carried out as follows: the panel is inserted into one guide profile, bent in an arc and then inserted into another guide profile. The side on which the small mounting shelf is located is inserted into starting profile. In order to bring the panel into the starting profile, you should use a rule and a mallet.

Video on installation of plastic facade panels

Plastic facade panels are quite interesting solution to decorate the facade of a building.