Distance between corrugated fence posts: calculation for chain-link. Instructions for installing a chain-link fence What is the best distance between fence posts

It is easy to build a fence from corrugated sheets with your own hands. In order for the construction of the fence to proceed without overlays, it is necessary to provide for everything in advance technical points. The basis of the fence is support posts and logs; this is the most labor-intensive part of the work. Maximum possible distance between fence posts made of corrugated board will significantly reduce the cost of fencing. At the same time, too long runs will make it difficult to install corrugated sheeting on the sheathing and reduce the strength of the structure. The optimal distance between fence posts is approximately 2.5 meters. Depending on the design features fencing, this figure may change in one direction or another, but not more than 3 meters.

The distance between fence posts depends on the material and method of installation of the supports. The more firmly the pillars are installed, the greater the distance between them can be. The distance is also reduced if the height of the fence is 2.5 meters or more.

Brick fence supports have the greatest load-bearing strength. Fencing is also erected using a metal pipe, metal profile or on stilts.

Poles must be placed in the corners of the site and in places where the fence changes direction. The locations of the supports are marked with pegs, a rope is pulled between them, and if the straight line is violated, they are aligned. They plan the gate and wicket.

Brick supports

Brick columns as supports look beautiful, are not subject to corrosion, and do not need to be painted. This solid structure requires the construction of a solid foundation, otherwise the fence may become skewed.

For the base of the masonry, pipes with a diameter of 57 mm or 2 to 4 rods of thick reinforcement are used. The distance between corrugated fence posts in finished form will be 2.6 meters, and between pipes - 3 meters. It is better to make supports from facing bricks- it looks better. Expenses are planned based on the calculation of 80 pieces per column.

How to make a foundation for brick pillars

A strip fence is installed under the fence with brick posts. concrete foundation 0.6 m wide. Depth into the ground of at least 0.5 m plus a 20 cm sand cushion. The protruding part is 25-30 cm high. It can be made of concrete or laid out in brick, and then lined natural stone, tile, plaster or paint.

To protect the edges of the corrugated sheet from below and from the sides, a groove is provided in the base and in the posts. This is more difficult to do in columns. Can be used for laying half bricks. After installing the corrugated sheeting on the joists, the grooves are sealed with cement.

Dig a trench, depending on the distance between the fence posts metal pipes(the usual figure is 3 meters). They are dug in to a depth of 25-30 cm below the freezing level. Then 2 layers of roofing felt are placed in the trench to waterproof the foundation. A frame is knitted from reinforcement 10 mm thick at a distance of 5 cm from the edges of the pit. The formwork is installed and poured with M300 concrete. Control the supports by plumb line.

If there are differences in soil on the site, then the foundation strip is divided into sections with a height difference of 10 cm.

Construction of brick pillars

Brick pillars under a fence made of corrugated board are placed one and a half or two bricks wide.

Their height is from 2 to 3 meters; the masonry is covered with metal caps or a cement slope on top. During masonry, metal mortgages are installed to secure the logs. The distance between corrugated fence posts with brick pillars in the final version it is 2.6 meters. This is taken into account when cutting the sheathing profile and selecting the width of the sheet.

Metal pipe supports

Use a round metal pipe with a diameter of 60 mm, metal thickness 2 mm. For a high fence, it is convenient to take 11-meter pipes and cut them into three parts.

The length of the pipe section for support is equal to the height of the fence plus another half of it for the underground part. If the fence is 2 meters high, then 1 meter of the support goes underground, the total length of the pipe section will be 3 meters. In this case, the distance between fence posts made of corrugated sheets can be made to a maximum of 3 meters, and even a little more (depending on the layout of the area).

Installation of metal pipe supports

The pipes must first be welded on top or other plugs installed to prevent precipitation from entering. If you weld a cross of reinforcement onto the lower edge of the pipe, the stability of the support will increase.

Install corner posts, stretch the twine at a distance of 30 cm from the ground and along the top. Places for holes for posts under the corrugated fence are marked. The holes are made with a manual or electric drill to a depth of 1-1.5 m with a diameter of 30 cm. It is recommended to wrap the walls with roofing felt - this will prevent the earth from crumbling. This will also protect the supports from deformation when the soil settles: the soil will slide over the roofing felt.

Crushed stone or gravel is poured to the bottom - 20 cm, a pole is installed (it should not pierce the pillow, otherwise corrosion is possible) and concrete solution is poured to ¾ of the depth. Align the support with a plumb line, wedge it with pieces of bricks, and top it up. If there is a slight distortion, then you can level it before the concrete hardens. Concreting is level with the ground surface, or even better, make formwork 40-60 mm and raise top part above the ground.

Concrete composition: 1 part cement, 4 parts sand, 4 parts crushed stone, 4 parts water.

The final hardening of the solution occurs within a week. Only after this they begin to install the sheathing.

If there is little precipitation (the annual norm is up to 300 mm), the soil is sandy or loamy, then it is possible to do without concreting. The pipe is dug in one third, wrapped in roofing material or doused with molten bitumen. The soil is poured in 20-25 cm portions, compacting each layer thoroughly.

IN dacha version you can build a fence from corrugated sheets with pillars from a free-flow asbestos-cement pipe with a diameter of 100 mm. Its length is 3.95 m. Cutting in half, you get two columns. The material is cheap but fragile.

Fence posts made of corrugated sheet metal

Use a 60x60 profile. Its length is 6 m or more, so you should take care of the delivery method in advance. Supports are installed from metal profiles in the same way as from pipes. Its advantage is that it is easier to install logs on it, and you can make a butt connection. This is more aesthetically pleasing; the strength of such a structure is increased by attaching the corrugated sheet to the pole.

Ready-made poles for corrugated sheets from a local manufacturer are sold on the market: They already have a capped top, a welded heel (can be placed on a sand bed), and have feet for joists with holes. The price is comparable to the price of the profile plus welding costs. The diameter of the pit for such supports will be two sides of the thrust bearing, and the distance between the fence posts can be 2.5-3 meters.

Installation of a fence made of corrugated sheets on piles

Ready-made foundation piles are expensive: 2000-2500 rubles apiece. But if you suddenly got hold of used material, you won’t find better supports. Their strength is very high, there are no costs for concreting and excavation. What is the distance between fence posts on screw piles? Again, it all depends on the height of the structure. With a fence height of 2.5 m, you cannot make too large runs, since the fence made of corrugated sheets has a very large windage.

An option for craftsmen is homemade piles. A pipe of the required length is flattened at the end into a spear. A ring of three pipe diameters is cut out from a sheet of steel 3 mm thick using an autogenous machine. A circle the size of the pipe diameter plus 15% is cut out inside, a groove is cut, made into a screw and welded onto the pointed end of the pipe.

Installation of sheathing

After the concrete has hardened, installation of the sheathing begins. Logs can be wooden or metal.
Wooden logs are short-lived and less durable. Therefore, let’s take a closer look at the metal sheathing. Use a 30x30 or 40x20 profile (attach the flat side to the fence), metal thickness 1.5-2 mm. Sometimes a metal corner is used, but it is inconvenient to attach a profiled sheet to it.

If the height of the fence is up to 2 m, 2 logs are planned, higher - 3 logs. The distance between the logs is about 1.6 m, 20 cm away from the upper and lower edges of the fence. If the distance between the posts of a corrugated fence is 3 m, then it is better to weld the profile not from above, but between the supports. This increases the strength of the structure and gives the fence a more aesthetic appearance.

Anti-corrosion treatment is also best done after cutting the joists, before welding. It is possible after, but it is more labor-intensive. In any case, the welding areas are cleaned and painted. If you install the sheathing without welding - screw it in - the strength of the structure will be lower.

Installation of corrugated sheets

The distance between fence posts made of corrugated board should be taken into account when choosing corrugated board. For the fence, use profiled wall sheets C8, C10, C20, C21. The most popular sheet is C15 - it is cut without an upward wave, so it is convenient to combine it. The width of standard rolled products is from 800 to 1850, the most popular is 1100 - 1180, length (height) is 1440-3000, up to 4500 can be ordered - it will cost more.

The height of the lower edge of the fence from the ground is 15 cm. If the surface of the site is uneven, then differences of 10-15 cm are made. Install the sheets with an overlap in one wave, fasten after 1-2 waves (if less often, it will rattle in the wind), or 20- 25 cm, in the depression of the profile.

Installation is carried out with metal screws using a screwdriver or with rivets (pre-drill holes) using a rivet gun. Rivets are identical to self-tapping screws, only gray, but such a structure cannot be disassembled.

How to extend the service life of a corrugated fence

To protect against corrosion, a metal profile is additionally installed below and above. It, as well as the metal sheathing and supports, will have to be painted approximately once every 3-5 years. Otherwise, corrosion will make itself felt. Alas, the only way not to paint fences is with brick posts. Not only fencing is made from corrugated sheets, as it is an inexpensive and fairly durable material.
By being careful when installing the sheet, you will save yourself from the need preventive work further. Use self-tapping screws with an EPDM gasket that protects the sheet coating from damage. During installation, paint over scratched areas with spray paint. Also, in the future, regularly treat scratches that arise during use.

A fence made of corrugated board, built taking into account all recommendations, does not require special care in the future it will last for more than a dozen years.

Modern technologies make it possible to build a fencing structure for a dacha or suburban area with your own hands and in a fairly short time. But in the process of carrying out work it is necessary to take into account many important characteristics. Therefore, let's talk in this article about what should be the distance between fence posts various types. After all, the strength and durability of the entire structure depends on this parameter.

Distance between corrugated fence posts

Installation in the right step

The distance between two adjacent support columns of a fencing structure in a country house or suburban area- this is the step with which these supports should be installed in the ground. However, it is important to clarify here next moment: This is not a universal setting. That is, for each individual type of fencing, experts recommend adhering to a certain value, measured in meters. Then the fence at your summer cottage, built by you yourself, will certainly please you with its durability and strength.

Let's talk in more detail about the different values of this parameter in certain specific cases.

Rabitz

Chain-link fences have become very common lately. This can be explained by the ease of installation of such a fence and its cost-effectiveness. To make the site more attractive, many summer residents plant vines next to it, which curl very beautifully over a metal mesh:

Experts say that the most suitable width metal mesh for a garden fence it is 1.5 m. But if you want to make the structure taller, you can raise the top edge of the mesh to the height of your choice. And the lower part of the structure can be laid with any material at hand. For example, bricks or wooden boards are used for these purposes;

If we talk about the required quantity support pillars for installation of a product made from chain-link mesh, this indicator is calculated based on the measured length of the fence and the selected distance between its supports. That is why it is important to clearly determine the optimal distance between the posts of a chain-link fence. Practice shows that to ensure the strength and reliability of the entire structure, this figure should be equal to 2.5 m.

Made of brick

People have been using bricks for many years in the process of building fences for country houses and suburban areas. Examples of such buildings are shown in the following photos. This trend is due to the high performance qualities of this material. Brick is valued for the following characteristics:

high strength;
durability;
reliability;
attractive appearance.

Brick columns are laid in the usual way using cement-sand mortar and mandatory ligation of stitches. If you undertake to do the masonry with your own hands, make sure that the support is horizontal and vertical. To make the product more attractive, add decorative stitching to the seams.

In the process of building a brick fence post, you need to install two embedded parts on all sides of the support into the masonry. This is done in order to subsequently be able to secure the spans, wickets and gates of the structure.

To determine required height fence posts made of bricks, you need to know the height of the structure. Typically it varies from 2 to 3 m. The distance between the support columns will depend on the width of the spans. However, experts do not recommend installing brick supports more often than every 2.5 - 3 m.

From corrugated sheets

The optimal material for creating structural pillars from corrugated sheets is considered profile pipe made of metal:

If we talk about the distance between the support pillars in in this case, qualified experts advise sticking to 2 - 2.5 m. Such span sizes will give your fence the required level of rigidity and flexibility, but will not allow it to break under the influence of strong gusts of wind;
The length of the pillars will be determined by the size of the profiled sheet used, as well as the characteristics of the soil in your suburban or summer cottage.

Knowing the step with which you will install supports for a structure made of corrugated sheets, you can easily calculate required amount supports

Made of wood

Wood is the most common material in country and country construction. It is highly environmentally friendly and available material, which explains its popularity.

When constructing a wooden fence, the distance between its supports is often chosen, which is 2 - 3 meters. Be sure to consider next fact: the higher your wooden structure is, and the wider its spans, the more securely you will need to fix its supports.

Logs or metal pipes of various shapes can be used as posts for such a fence.

From a picket fence

Let's talk separately about wooden picket fences. They are one of the most frequently erected types of similar structures in private construction. They delineate the boundaries summer cottage, but, at the same time, they do not at all shade the plants that grow next to them. This design of fencing looks very attractive.

You can give fences for a summer cottage, built from picket fences, any height, shape, color shade. The installation distances of the support pillars can be any. For these reasons, such designs have a very original and attractive appearance. Look at the following photo to see this.

Let's sum it up

The spacing with which support pillars of fencing structures are installed is a very important parameter on which their strength, resistance to gusts of wind and other loads, durability and reliability will depend. This fact should not be neglected, otherwise your fence will not please you with a long service life.

A fence made of corrugated sheets has an attractive appearance and allows you to fence any areas personal plot or enterprises.

At correct installation a fence made of corrugated sheets can last for many years, unlike wooden fences.

What is the maximum possible distance between corrugated fence posts that will significantly reduce the cost of fencing? But, at the same time, too long runs will make it difficult to install corrugated sheeting on the sheathing and reduce the strength of the structure.

Profiled sheet

Profiled sheet, also known as corrugated sheet. It is a galvanized sheet of metal coated with a polymer coating to protect it from atmospheric influences. It is made by cold rolling followed by profiling to impart rigidity to the sheet.

Profiled sheet is a building material that is used for the following purposes:

For roofing various buildings.
For cladding residential walls and non-residential buildings.
For the construction of external fencing.
For the construction of load-bearing designs.
For the manufacture of non-removable foundation formwork.
For making greenhouses and heat c from sheets of profile polycarbonate.

Profiled sheet is produced various types, which have the following differences:

Application area(roof, bearing structures, fencing).
Waveform(slate or trapezoidal).
Wave height from 8 to 21 mm.
Wave width.
Sheet thickness from 0.4 to 12 mm.
Sheet coating:
- Polyester;
- Acrylic
- Polyvinyl chloride
- Polyurethane.
Weight of one square meter from 4.5 to 17.5 kg.

The profiled sheet has the following markings:

H- Used for roofing walls.
C-Preferably used for wall cladding and fencing.
HC-Used for roofing as wall corrugated sheeting.

Like all materials, profiled sheets have their advantages and disadvantages.

Advantages:

1.Easy to install.
2. Light weight of the material.
3. Good protection from corrosion.
4. Big choice color palette.

Flaws:

1. Easily deformed.
2. Loss of corrosion protection when the sheet coating is damaged.

Profiled sheet is relatively inexpensive construction material, which can also be attributed to its advantages.

What materials are corrugated fence posts made of?

To build a fence you will need: logs, corrugated sheets, pillars.

Lags in the form of rectangular profiles and guides for profiled sheets 2.5 m long.
Corrugated sheet or profiled metal sheet with polymer painting to withstand any negative impact and precipitation
Pillars in the form of pipes up to 60 mm in diameter or square profiles with optimal height 1.8 m. The pillars need to be buried 1,200 mm. The approximate height of tables should be at least 3 m.

Experts advise using grades of corrugated sheeting - C8 and C10:

width- 1200 mm;
height- 8 mm;
thickness sheet – 0.5mm.

These are fairly light sheets with a small thickness that can facilitate installation. The best option for fastenings for corrugated sheets would be galvanized self-tapping screws. It is advisable to select them by color in combination with profiled sheets. The distance between the pillars will depend on the selected material and the method of installing the supports. The stronger the pillars are, the greater the distance between them must be maintained.

The most durable ones for fencing are:

brick supports;
metal pipes.

Before installation, it is important to take into account changes in the direction of the fences, for which you mark the places with pegs, pull the rope, thereby aligning the expected borders of the fence.

Brick supports

Brick pillars- a favorite material for fences among home craftsmen, because... wood is not strong enough, and metal requires special attention.

Create concrete structure long and expensive. The brick support is considered a universal design, suitable for any fence (wooden, brick, metal).

At the same time, the construction of supports does not require the purchase and use of expensive equipment.

Attractive performance and the appearance of the brick. Material:

lasting;
qualitative;
not subject to corrosion;
not requiring additional coloring.

Brick supports require the construction of a solid foundation. To avoid distortions of the fences in the future, it is necessary to select pipes 57-58 mm in diameter and thick reinforcement up to 4 mm in diameter as the basis for the masonry.

Distance between posts if used for a fence:

corrugated sheet, then the distance between the pillars should be at least 2.6 m;
metal pipe, then the distance should be 3m;
facing brick for supports, you need to purchase so much material that it takes approximately 70-80 pieces for 1 pillar.

Costs depend on the height of the proposed fence and the degree of load on the foundation. The fence must withstand winds, so depth calculations when installing posts must be made correctly.

How to make a foundation from brick pillars?

The foundation requires pouring concrete mortar. Best choice concrete grade 400 will become, which will last a long time and will not crack after hardening. To obtain the required volume of mortar without excess, you must first multiply the width and length of the foundation by the height, and also leave a little mortar for shrinkage.

On a note! The solution should not have time to harden as it is poured into the trench, so you need to calculate its required volume as accurately as possible.

The composition of the concrete solution includes: sand, crushed stone and cement in a ratio of 2 x 2 x 1.

You need to start work by pouring the raw materials into a concrete mixer and manually mixing. So for building a foundation for brick pillars, the technology is as follows:

mark the area along the perimeter with a cord when placing a strip foundation;
dig a trench up to 50 cm deep and up to 45 cm wide;
form drainage or crushed stone cushion;
lay the reinforcement to the bottom of the pit: first 2 rods horizontally, then 2 more at the top of the pit parallel to the bottom;
install brick pillars as more heavyweight;
additionally can be laid across the rods for the purpose of reinforcement with a cross section of 1.4 cm;
pour into the trench solution so that there are no voids inside the base.

To increase efficiency, the work is done manually or with a deep vibrator. The finished foundation must be covered from above to prevent exposure to floating sun rays and cracking as it hardens. Will remain above the ground to form wooden formwork, install the boards at a certain height along both parts of the trench.

When concrete base completely hardens (in about 2 weeks), then the formwork can be removed and work on the fence can continue.

Construction of brick pillars under a corrugated fence

Under a corrugated fence, brickwork is made 1.5-2 bricks wide and up to 3 m high. A cement slope or metal cap is installed on top of the masonry to cover the structure. The main thing is to maintain the distance between the pillars. When installed at the outlet, it should be at least 2 - 2.6 m.

Attention! Experts do not recommend placing pillars on top of the foundation, because under the influence of the load, their gradual destruction, deformation, and rapid destruction of the brickwork are possible, which will be subject to additional load in the form of a gate or wicket.

It is better to use the following material for pillars:

facing brick;
metal supports (fittings, pipes, corners) reinforcing the pillars;
other fasteners for subsequent installation of logs.

If the pillars are hollow, they can additionally be filled with concrete. You need to dig to a depth of up to 90 cm, in particular, at the time of laying the foundation, be sure to seal the distances between the supports and brick pillars with mortar, adding broken brick and crushed stone for strength.

It is important to ensure that all voids inside the post are properly filled in order to give greater strength to the fence. Before installing sections of pillars, you should wait until the foundation is completely dry. At least 3 weeks must pass before it is possible to install the sections and hang the gate.

For supports, it is preferable to use metal pipes 60 mm in diameter and 2 mm in thickness. If you plan to build a high fence, then the pipes should be 11 m long for the purpose of cutting into 3 parts, and the length of the segment should be equal to the height of the fence.

Additionally, you need to leave the pipe size for the underground part- half the height of the fence itself. Thus, with a fence 3 meters high, approximately 1.5 m will go into the ground, so the length of the pipe must be 4.5 m. In this case, the distance between the fence posts made of corrugated sheets can be made to a maximum of 3 meters, and even a little more (depending on the terrain layout).

It is advisable to prepare the supporting surface in advance:

treat against corrosion;
paint with waterproof paint;
clean with a brush if necessary.

Installation of metal pipe supports

To install the supports, holes are drilled in the soil manually (mechanically). The diameter of the hole in the soil must match the diameter of the support. The process for deepening the supports is as follows:

drill holes;
pour the foundation;
bury each pipe separately to the required depth;
deepen the supports or set them vertically, using a level for evenness;
leave gaps along the edges of the pit;
fill with sand;
compact, having previously concreted the base.

To install metal supports, you will need a concrete vibrator with a core to bury the posts, which you need to think about in advance. The concrete pouring should be of a dense consistency, without any air cavities inside. It is important to protect the pipes from direct sunlight after pouring concrete and leave them for 2 weeks to gain strength. Next, install a grillage to give greater rigidity to the structure or tie the supports together, connecting them to the overall structure.

When calculating the distance between metal supports, it is necessary to take into account the height and length of the fence, the cross-section of the supports, and the number of required posts. So, when installing a fence made of corrugated sheets, the maximum distance between posts is 3 m; when erecting brick supports, the distance must be maintained at 2.5 m; when erecting wooden supports, 2 m.

Fence posts made of corrugated metal profiles

The following sizes are suitable for use as profiles:

diameter - 60 x 60;
length - up to 6m.

The technology for installing metal profiles is the same as when installing supports made of metal pipes. Although the profile the better that you can install logs on them. At the end, the fence turns out to be more durable and aesthetically pleasing thanks to the fastening of the corrugated sheet to the posts.

Today the best options The market considers sheets with a welded and plugged top and holes for joists for the purpose of quick, easy installation. The main thing is to endure correct distance between the pillars of metal corners 2.5-3 m. It is recommended to use solid profiles in work, because they will last much longer.

Installation of a corrugated fence on piles

The distance between the piles will directly depend on the height of the structure being installed. If the expected height of the fence is 2.5 m, then it is not recommended to make unnecessarily large runs, because light profiled sheets will quickly begin to fray from a slight wind load.

Many home craftsmen prefer to install homemade piles with their own hands. Option for installing a fence made of corrugated sheets:

flatten the pipe at the end in the form of a spear with an autogenous gun;
cut rings from a pipe;
cut grooves slightly larger in diameter than the diameter of the profiled sheet;
smash fence corners;
at the corners of the borders install pillars maintaining a distance of 2.5 m;
arrange the pegs along the perimeter of the fence, leaving a distance for a wicket or gate;
pull the rope between the stakes, mark the location of subsequent posts along it;
dig a hole, produce a sand cushion up to 100 mm thick;
install pipes, fix before pouring concrete;
commit wooden spacers at the top of the posts;
set extreme supports, pull a rope between them;
install all subsequent ones;
pave waterproofing layer.

Attention! Before installing the structure, it is recommended to paint the ground part with waterproof paint, and top ends equip with plastic plugs to prevent water from getting inside. If the pillars are hollow, then for strength, their insides can be filled with concrete, just like the base.

REFERENCE! To avoid compromising the integrity of the structure at the corners of the fence, sheets of corrugated sheets should be bent rather than cut. Lastly, you can lay a decorative fence strip and screw it with inside fence Place the corrugated sheet on the press washers so that the screws are invisible from the outside.

Advantages of a fence made of corrugated sheets

Fencing made from profile sheets has high demand, since a fence made of corrugated sheets has a number of advantages over fences made from other materials:

Simple process installation and installation.
Does not require large financial and time costs.
Has an aesthetic appearance.
Has the ability to combine forged elements.
When building a fence you can combine materials (brick and corrugated sheets, etc.).
It has long term services.
Strength of the fence structure.
Easy maintenance process.
Large selection of colors.

At making the right choice materials and high-quality installation, a fence made of corrugated sheets will last for many years.

Required tools and materials

To manufacture and install a fence made of corrugated sheets, the following building materials are required:

Profiled sheets such brands C8, C10, C16, C18, C21.
Roofing screws with hydroshades or rivets.
Metal pipe with a diameter of 76 mm or a profile square 60x60 mm.
Metal profile 45x25 mm or wooden beam the same sizes.
Cement brand M 400 and screenings for concrete production.
Wooden boards for formwork at least 250x20 mm and a length of at least 3 meters.

To make a fence from corrugated sheets and install it, you need the following tools:

Electric drill or a screwdriver.
Screw bits and a 10 mm drill.
Angle grinder(grinder) with a nozzle for metal.
Water level.
Metal scissors.
Nylon thread.
Hand drill for drilling holes for poles.
Welding machine.
Rivet gun(if fastening is done with rivets).
Means of protection: mittens, glasses, etc.

When choosing materials for a corrugated fence, you should not skimp on the quality of the material, as this will affect the service life of the fence.

Installing a corrugated fence with your own hands

Installing a fence made of corrugated sheets does not cause any particular difficulties, having in stock necessary tool you can make it yourself.

The process of installing a corrugated fence consists of the following steps:

Perimeter marking. The first step in installing a fence is marking the perimeter, it allows you to calculate the number required material for fencing and install the posts evenly.
Marking can be done using a nylon thread, stretching it along the site from one corner to another and so on along the entire perimeter of the fenced area.

Also, when marking, it is necessary to note where the fence posts will be installed.
Installation of support pillars. To install the pillars, you will need a drill, which will need to drill holes with a depth of at least 75 cm and a diameter of at least 25 cm in accordance with the markings at the optimal distance from each other.
After the holes have been drilled, the support pillars are installed, leveled, or the voids around the pillar are filled with concrete.
When pouring concrete, you should make sure that the installed pillars do not move from the set marks, as this will cause the fence to skew.
Installation support joists. After the pillars are installed and filled with concrete, you can begin installing the support beams on which the corrugated sheeting will be attached. Installation is done using welding machine or long screws.
Installation of logs is carried out horizontally in 3-4 pieces (depending on the height of the fence) between the pillars, starting from the bottom.
When installing logs, the distance between them should be no more than 40 cm; this is necessary to give the structure greater rigidity.
Fastening corrugated sheeting to a metal frame. The corrugated sheeting is fastened to the constructed frame using roofing screws or rivets. Self-tapping screws must be screwed into the inner wave of the sheet and at least through one wave. Fastening with rivets is done in the same way as with self-tapping screws.
Before attaching a sheet of corrugated sheeting to the structure, it must be leveled or using a stretched nylon thread.

Installing a fence from corrugated sheets yourself will not cause any particular difficulties and will turn out to be of high quality if you follow the processes described above. Also, when installing a fence, it is worth remembering the safety rules for working with power tools.

Caring for a corrugated fence

Just like installation, maintaining a fence made of corrugated board does not cause any particular difficulties. For proper care behind the fence you must follow some rules such as:

Clean the fence soap solution with a soft sponge.
Do not use for cleaning fences detergents containing solvents, as they can damage the polymer coating of the corrugated sheet.
Do not use abrasive sponges for cleaning the fence, since the coating of the sheets can also be damaged.
Washing a corrugated fence It is recommended to do this at the beginning and at the end of any season, since the edges of the sheets tend to accumulate dust and quickly become dirty.
Do not treat with chemicals solvents.
Avoid scratches and cracks, then the corrosion process will begin to occur faster. If scratches appear, it is advisable to immediately paint the surface or cover it with a clear varnish.
Do not allow fires near the fence eg during barbecues, exposing paintwork to high temperatures.

When washing the fence, do not wet it with plenty of water; just wipe the contaminated areas with a damp sponge and soapy water; you also do not need to wipe the fence dry. Periodic washing of a corrugated fence allows you to maintain its attractive appearance and significantly extends the service life of the fence.

The optimal distance between corrugated fence posts

The distance between posts for fencing made of corrugated sheets is set depending on the climatic conditions of the region. If the region often experiences strong gusts of wind, then the optimal distance between the posts will be 1.7 m.

The stronger the wind in the region, the smaller the distance between the pillars. As has already been said, a fence made of corrugated sheets has a large windage, and small distances between the supports reduce the load on the fence structure that occurs when strong winds occur.

If there are no strong gusts of wind in the region, a distance between posts of about 2-2.5 meters is allowed, but no more.

It should also be remembered that the distance between the logs also affects the strength of the fence and should be no more than 40 cm.

Lathing a fence made of corrugated sheets

How to extend the service life of a corrugated fence

The service life of a fence made of corrugated sheets primarily depends on high-quality installation and processing of the materials used for installation.

To significantly increase the service life of a fence made of corrugated sheets during installation, you should adhere to the following recommendations:

Bury fence posts to a depth of at least 75 cm. Along the perimeter of the future fence, fill the installed posts with concrete. Since a fence made of corrugated sheets has a large windage, such manipulations will prevent distortions of the fence from strong winds.
The metal frame of the fence must be carefully treated with anti-corrosion primer and painted with good durable paint. This will prevent corrosion processes for a long time. metal structure fence Since after installation of the sheets, painting the metal frame will be partially unavailable. Therefore, all painting actions must be carried out before installing the corrugated sheet. The only way to avoid painting fences is with brick posts.
It is best to use a metal profile as fence logs, since wooden beams have a significantly shorter service life. It is also recommended to use a thick-walled metal profile; a thinner one has short term service, since the corrosion process quickly destroys the metal structure.
The joists should be fastened to the support posts using a welding machine. Since when fastening the logs with self-tapping screws, the fence structure will not receive the necessary rigidity, which over time can lead to deformation of the sheets. For better reliability, you can screw the logs with self-tapping screws, and weld the joints with the support posts using a welding machine.

It is best to use metal poles for the structure. Installing a fence made of corrugated sheets is not difficult, the main thing is to know all the stages of the process and properly care for it in the future, so that the fence will delight you with stability and strength for many years.

One of the obvious advantages of fences made from a material such as corrugated sheets is that it is quite possible to build these fences with your own hands, without resorting to the help of expensive construction crews. The work is quite simple; after studying the instructions, in fact, any person who is familiar with the tool first-hand will probably be able to cope. But there are also relevant nuances. For example, one of the key problems is correct installation pillars How to cope with this task effectively? What should be the distance between corrugated fence posts, and how to calculate it correctly? After all, this is the main parameter that is designed to ensure the strength and durability of the structure. After all, even the most reliable material will not withstand the onslaught of weather conditions or an accidental mechanical shock if it is not securely secured with pillars. And they, in turn, will not bear the load when they are not installed according to the rules.

Basic principles

The basis of every “self-respecting” fence is posts with logs. And their installation is the most labor-intensive component of the entire work. Of course, the maximum possible distance between corrugated fence posts significantly reduces the overall cost and saves money. But too long runs make it difficult to install the corrugated sheet and “undermine” the strength of the structure. The optimal golden mean would be about two and a half, three meters. This figure may vary in one direction or another, but, as a rule, no more than 3. Also, the gaps between the supports directly depend on the materials from which the pillars themselves are made, and on the installation method (we’ll talk about these two nuances below). In addition, the more firmly the supports are rooted, the longer the distance between them can be. And when they build a fence with a height of more than 2.5 meters, then vice versa - shorter. Structures with brick pillars have the greatest strength. Metal pipes, profiles, wood and asbestos products are used as elements. So for those under construction the choice is quite large. It is important to follow some marking rules with installation, and an important safety function for your home or site is at your service.

An example of marking posts for a fence made of corrugated sheets

The pillars are the basis of the fence

In general, the structure on which the corrugated sheet is attached consists of:

The main supporting elements that are installed at the corners of the site and on the sides of the gate. Typically, these pillars are slightly thicker, as they experience increased loads.
Intermediate support elements. Often, for economic reasons, they are chosen thinner because they are less loaded.
Raskosov. These elements are used to level the supports in cases where soil parameters do not allow concreting to be carried out with proper efficiency.
Horizontal joists. They are constructed from beams, or from small section profiles (30x30, 20x40 millimeters).

Fence design drawing

All elements must be rigidly connected to each other. For this purpose, both welding and mechanical connectors are used. How to choose the right supports, because modern market provides different types of products?

A Question of Choice

Which supports are commonly used for corrugated sheet fences? The following types are widely used:

metal;
wooden;
profile;
reinforced concrete;
with brick pillars;
asbestos-cement.

Their length can be determined depending on the height of the canvas (as a rule, it is selected individually). The pillars are usually slightly longer than the selected height (per meter). The upper sections, if the supports are hollow inside, are welded, sealed, or a plug is installed - depending on what material they are made of. This prevents liquid from getting inside the racks.

Metal

This is the most common material for fence posts. Such supports are made from sections of round or profiled pipe with fairly thick walls (thickness of at least 2 millimeters, for tall structures - up to 3). The second option is more technically robust and looks much more presentable and modern. The length of the parts depends directly on the height of the fence. Depth into the soil - from a meter (on dense soils) to one and a half. The metal must be subjected to additional anti-corrosion treatment. And the upper segment of the support must be updated annually, covering protective compounds(for example, paint or varnish). The profile cut should be welded or an appropriate plug should be installed to prevent water from entering the product.

Profile posts for a fence made of corrugated sheets

Tree

This pole material is used in temporary structures. Wooden supports, of course, are inferior in their characteristics to those of metal or brick. But when it comes to saving, they are applicable quite often. Usually these are coniferous species: pine and spruce. The material itself is chosen with a sufficient cross-section and without large knots and cracks, even. Don't forget to treat the supports antiseptic- from pests. And lubricate the lower part with mastic to prevent moisture penetration.

Example of a base for a brick pillar

Concrete and brick

Factory-produced concrete structures are an alternative to the above supports. The product is made of sand, cement, building rubble. The post itself is divided into 2 sections: the lower one is embedded in the soil (0.8 - 1.2 meters), and the upper one is equipped with grooves for fastening the logs. Such products have reduced deformation from the effects of windage. As an option: with brick pillars, as well as in combination - brickwork and round pipe. This method is excellent in terms of strength and aesthetic appearance, but erecting a structure “on brick” will require more significant costs and additional work.

Asbestos cement pipes

Supports from of this material still hold a fairly strong position. After all asbestos cement pipes coated with a special composition can last for decades, requiring almost no attention - painting, processing! Low cost, resistance to humidity and pests - excellent a budget option. But each material has its drawbacks. Asbestos-cement products also have them. They are highly fragile, which makes them difficult to transport. The pipe is heavy and bulky, which makes installation difficult. You also need to prevent liquids from getting inside the product: when they freeze, they will expand and the column may split.

Asbestos cement pipes for supports

Pipe plug option from above

Work order

Let's say you have decided on the choice of supports, and now you need to proceed directly to installation. The simplest option is concreting (unless it is a short-term construction). Here rough plan work step by step.

We start by marking the area to be fenced. We mark the perimeter of the area with a measuring cord (we also use wooden or metal pegs).
Next, let's start applying markings, actually under the supports. The optimal distance for fences made of corrugated board, according to many craftsmen, is 2.5-3 meters - from pillar to post. This is directly related to the nuance that the profile used for installing horizontal joists on the structure is six meters long. Thus, when marking spans of the specified length, it is easier to join the logs.

Drilling holes for supports

Using a drill (see photo), we make holes in the soil at the marked points. The diameter of the holes for the pillars should be at least one hundred millimeters larger than that of the supports.
We fill the drilled holes with crushed stone. Compact with a tamper. We place each element separately, aligning it with a plumb line/level.
Fill the gravel on top (up to half) and fill in the cement solution.
We fix the pillars with boards or braces. When the solution has completely hardened, remove the fixation. Only then can the logs be attached.

Please note that installing corrugated fence posts according to the rules is an indispensable condition; it determines the durability of the structure and its strength. Experts advise not to rush at this stage, but to do everything thoughtfully - as described in the instructions. It’s better to spend a little extra time than to rebuild a “collapsed” fence later!

Be sure to watch the video:

Every sane owner land plot tries to protect the legal territory from the encroachments of ill-wishers. As a fence, a fence is constructed, which is built from various materials.

The choice of materials on the modern construction market is huge, but you can choose profiled sheets as a simple and reliable one. Visually it is beautiful and does not require special care. Before constructing this type of fence, it is necessary to take into account many nuances and recommendations.

Profiled sheet

Profiled sheet- this is a sheet of thin metal that has longitudinal recesses (corrugations) of varying depths and can be coated with a special paint and varnish composition. Depending on the consumer purpose, it has different thickness and length.

The sheet can be used as roofing, wall, and facade finishing material.

Corrugation height ranges from 10 to 114 mm. Low height (10 – 20mm) is used for finishing walls and fences. Average heights (20-60mm) are intended for roofing works. High profiles(60 – 114mm) are necessary for the construction of formwork (foundation).

Sheet manufacturers provide the ability to select a layer protective coating for him. This implies that the sheet can be painted special paint(polymer) in any color or remain galvanized.

The classification of profiled sheets occurs according to their purpose, the presence of a protective coating and the quality of the blank material.

Destination types:

N– the sheet is intended for flooring.
NS– the sheet is intended for flooring and wall fencing.
WITH– the sheet is intended only for wall decoration.

Material for the original workpiece:

Galvanized thin sheets.
Thin sheet metal coated with aluminum-zinc coating.
Thin-sheet aluminized rolled products with silicon coating.
Thin sheet metal with zinc coating.

Availability of protective paint coating:

Galvanized sheets with a silver tint.
The sheets are covered with paint in different colors.

Advantages of a fence made of corrugated sheets

The material has a low cost compared to brick or oak picket fence.
Visual appeal, because from the outside it looks monolithic.
Fast installation.
During the construction process, the use of heavy equipment will not be required.
Possibility to choose the shade of the sheets.
Profiled sheets will last at least 8 - 10 years without additional repairs.
From sheets you can make not only a fence, but also a wicket or gate.
Minimum number of components for installation.

Required tools and materials

The tools you will need are:

Grinder with a circle for metal 1.5 mm thick.
Metal scissors.
Long carrying capacity with the ability to connect to a 220 V network.
Drill and screwdriver.
Hex adapter for combination with the heads of special self-tapping screws.
Bayonet and pick-up shovel.
Sledgehammer.
Manual tamping.
Roulette and building level.
Welding machine and electrodes.

Necessary materials:

Profiled sheets.
Round metal pipe (diameter 100 mm, thickness 5 - 6 mm) or square profile (10 × 10 cm, wall thickness 5 mm).
Rectangular metal profile 20×40 mm with a thickness of 2 – 2.5 mm.
It is possible to use concrete and rubble stone to strengthen the pillars.
Special self-tapping screws with rubber waterproofing gasket.

Installing a corrugated fence with your own hands

The construction of the fence must take place in stages, which includes:

Accurate marking of terrain and locations for support pillars.
Installation of pillars.
Installation of logs between pillars.
Attachment metal sheets to the frame.
Installation of gates or wickets.

Perimeter marking

Along the entire length of the future fence, marks are placed on the ground for support posts, both for the fence and for the gate or wicket. This can be done by driving wooden pegs into the ground or simply pouring a pile of sand.

When marking, it is necessary that the marks are located at the corners of the fence and in places of possible bends (changes in the straight direction). To ensure that the pillars are in the same plane, a nylon thread is stretched between the corner pegs, which will later serve as a guide for the intermediate pegs.

Installation of support pillars

Initial stage installing pillars (supports) in the ground involves digging holes, but not all of them in a row, but those in which the main (guide) supports will be installed. This corner places and places of bends. The depth of the pits should be at least 1.2 - 1.5 m and a width of 15 - 20 cm, which contributes to the stability of the pillars under various types of influence on them (mechanical or natural interference).

Next, pour into the bottom of the hole a little coarse crushed stone and compacted. After this, you need to measure the depth of the hole and transfer (mark) this indicator to the surface of a round pipe or square profile. To the indicated length it is necessary to add the height of the corrugated sheet and also add 2 - 3 cm, which will serve in the future bottom gap between the soil and the sheet (natural ventilation).

When all the marks have been made, an unnecessary section is cut off from the total length of the profile with a grinder.

Having prepared the profile for installation, it is placed in a hole and 1/3 of the depth of the hole is filled with crushed stone. A layer of pre-prepared concrete is poured on top of it. During pouring, it is necessary to monitor the vertical level of the post. According to this scheme, all other corner pillars are installed, but at the same time, monitoring their height relative to the ground.

To avoid discrepancies in performance, a rope is stretched between their tops, which should show a horizontal zero mark when checking it with a building level.

When the main pillars are installed, you should proceed with the installation of intermediate pillars according to the same principle. Stretched auxiliary guide ropes guarantee the correct location of the posts and their surface height. In order to prevent moisture from penetrating inside the support pillars, their upper part is welded with metal plates.

Eg, if a sheet 2 m long is selected, and the depth of the dug hole is 1.2 m and a gap of 3 cm is selected, then the length metal pole should be 3.13 m, taking into account a 10 cm layer of crushed stone previously poured onto the bottom.

After installing all the pillars V construction works stop for 7 - 10 days so that the concrete acquires the necessary hardness.

There is another method of installing pillars– manual driving into the ground. To do this, one person holds the pipe in a vertical position, and the second hammers it in with a sledgehammer on the top of the pipe. It is worth noting that this method requires enormous physical expenditure and time from the participants in the process, therefore it is of little use in construction.

Installation of support beams

In order for the profiled sheets to become a full-fledged fence, it is necessary to build a metal sheathing between the posts to which they will be attached. To do this, it is necessary to secure the logs between the pillars.

The number of lags may vary, depending largely on the height of the sheets. For standard height a sheet of 2 meters requires two parallel logs at the bottom and top of the pillars, respectively.

Marks are made on the pillars at the top and bottom along which the logs will be mounted. It is necessary to retreat 20 cm from the upper and lower edges. The width between them will be within 1.6 m, which is quite acceptable. They are used as lags metal profiles with a section of 20×40 mm or 20×45 mm.

To secure the profile between steel posts, you first need to measure the distance between them and use a grinder to cut the required piece from the workpiece. It is recommended to fasten by welding, which guarantees the reliability of the joining points.

If experience welding work absent - you can fasten the profiles using L-shaped metal corners, but this process has several disadvantages: labor-intensive and time-consuming. And the most important nuance of this type of fastening is possible loosening fastening elements and subsequent vibrations of all sections of the fence.

Fastening corrugated sheeting to a metal frame

When the frame is assembled with your own hands and tested for strength– you should begin installing the corrugated sheet. To carry out fastening, at least two people will need to be involved in the process. One will hold the sheet correctly relative to the frame, and the second will fasten it.

You should start from one of the corner posts. When leaning the sheet against the frame, you need to monitor the horizontal and vertical planes sheet, because in the future the slightest deviations from zero mark threaten with uneven sheets.

After leveling the sheet, it is secured to metal joists special self-tapping screws with a drill-shaped tip. This type of self-tapping screw does not require conventional drilling of holes - it will go deeper into the body of the profile itself. Thanks to the wide hexagonal head with a rubber gasket, the self-tapping screw securely fastens the corrugated sheet and does not scratch its surface.

Initially, 4 screws are enough for one sheet, screwed into its corners. The second sheet is leaned against the first in such a way that the joining strips overlap and are fastened in the same way. The whole process is repeated identically with all subsequent sheets.

Upon completion of fastening all sheets along the perimeter or a separate part of the fence, you need to return to the first sheet and secure it completely. To do this, a self-tapping screw is screwed into each recessed wave of the sheet. Fastening the remaining sheets is repeated identically to the first. When the top and bottom sheets are properly secured to the frame, the fence is considered almost ready.

Caring for a corrugated fence

A modern fence will last longer if you follow a few rules:

When contamination in the form of oil stains appears on the surface of the sheets or a heavy layer of dust, they must be removed using warm soapy water and a soft cloth. The wet surface is immediately wiped with a dry cloth so as not to leave streaks.
Do not use abrasive sponges or similar analogues when cleaning the surface.. They can damage the paint layer, and in the future the metal may be subject to corrosion.
After cleaning the sheets do not need in additional polishing with wax aerosols.

The optimal distance between corrugated fence posts

The distance between brick pillars or imitation brick can be from 2 to 3 meters. Many experienced specialists recommend a distance of 2 -2.5 meters. This perfect option for convenient fastening of sheets and reliability of support posts.

Of no small importance is the possibility of non-joining (welding) of two profiles with a larger width, because the standard length of a profile is considered to be 2.5 m. Solid profile - will last much longer.

How to extend the service life of a fence made of corrugated sheets?

Since the material for the fence is quite durable (designed for 25 years of service), it does not require special care, but Some nuances during operation should be adhered to:

Do not clean the surface with metal brushes or use powder detergents.
Do not treat the surface chemical solutions, namely solvents.
Prevent the appearance deep scratches, which expose the metal to the corrosion process. If they are detected, they are immediately painted over with paint or clear varnish.
Do not light a fire near the fence or install a barbecue, because high temperature The paintwork may crack.
All metal carcass and the pillars must be coated with a special water-repellent impregnation once a year.

Conclusion

Installing a fence made of corrugated board is quite simple and does not require high knowledge of the process. The fence will please the eye long years and without special methods of caring for its surface. This type of fence is an ideal budget option for all land owners.

Every owner garden plot, a private house will sooner or later ask the question of what distance is needed between fence posts when planning the aesthetic design of the boundaries of their estate. Man is designed in such a way that he tries to define his possessions, to fence them off from the outside world. It could be hedge, decorative fence, massive fence that reliably hides privacy owners from prying eyes. It is clear that in any case, the fence performs decorative, barrier, and protective functions.

Everyone chooses for their site the type of fencing that can best cope with the main function assigned to it, in the owner’s opinion. A new fence can not only bring a new mood to the garden and site, but also create a feeling of security, coziness and comfort.

The construction of a fence should not be approached lightly, because it is the “face” of the property. The fence must be strong and reliable. A fallen fence, even the most elegant one, will not decorate the courtyard. That is why it is necessary to pay enough attention to calculating the distance between the support posts.

To cover all possible options for arranging site fencing, we will consider the following types:

decorative fence from ready-made sections;
concrete fence or stone (brick) fence;
temporary fence.

Calculating the distance between fence posts must begin with marking the area and installing corner marks, because in these places the presence of posts is mandatory.

Hedge or fence made from ready-made sections

In the case of a hedge, there is no need to install supports. Whereas for any other fence, the correctly calculated location of the support pillars is the key to the reliability of the fence and the longevity of its service.

Regardless of material of manufacture decorative fencing(plastic, wood, metal or other material), the dimensions of the sections determine the height of the column (taking into account the part immersed in the ground).

The distance between the supports will correspond to the width of the fencing sections. It is also necessary to take into account the type of fastening of the sections to the supports (overlapping - the section overlaps part of the support, or in the opening between the supports - the fastenings are located on the sides of the support posts).

Optimal distance between pillars

It is necessary to take a more responsible approach to calculating the spans between pillars if you plan to build a fence made of concrete, brick, masonry or even chain-link mesh.

The strength and durability of such a fence directly depends on the correct location of the supports.

For fences made of concrete or masonry, additional horizontal fasteners in the form of logs are not used, and the recommended distance between the supporting elements of the structure is 2-3 m.

It is economically advantageous to place supports for such fences at a distance of 2.5 m.

The fence will be very reliable, not “overloaded” with massive supports, the financial costs of installing which constitute a significant part of the cost of the entire fence, since installing such supports is a very labor-intensive process.

When calculating the distance between supports, it is necessary to take into account the length of the horizontal runs (logs) used.

This will significantly simplify installation, facilitate the joining of wires, and optimize the financial costs of installing the fence.

The most common logs are 3 m and 6 m long. Therefore, the optimal distance between the posts should be no more than three meters. In the case of using 2.5 m or 5 m long veins, the recommended distance between posts is 2.5 m.

For a temporary fence made of wire or mesh, the optimal distance is 1.8-2 m. It is this distance that allows the mesh (wire) to be well tensioned, eliminating the sagging effect. In order to save money, permanent supports are placed under the temporary fence at a distance of 3 m from each other, but for strength it will be necessary to stretch wire veins through the mesh. Then the mesh will not sag or collapse. Subsequently, it will be enough to remove the temporary mesh and mount a barrier on the existing posts.

It may seem that building a fence is a complex and very responsible task. It’s only the eyes that are afraid, but the hands that do it. The main thing is to think everything through well, calculate it, go out to the site, start marking, and then everything will go as usual. All that remains is to start and finish.

One of the obvious advantages of fences made from a material such as corrugated sheets is that it is quite possible to build these fences with your own hands, without resorting to the help of expensive construction crews. The work is quite simple; after studying the instructions, in fact, any person who is familiar with the tool first-hand will probably be able to cope. But there are also relevant nuances. For example, one of the key problems is the correct installation of poles. How to cope with this task effectively? What should be the distance between corrugated fence posts, and how to calculate it correctly? After all, this is the main parameter that is designed to ensure the strength and durability of the structure. After all, even the most reliable material will not withstand the onslaught of weather conditions or an accidental mechanical shock if it is not securely secured with pillars. And they, in turn, will not bear the load when they are not installed according to the rules.

An example of marking posts for a fence made of corrugated sheets

The pillars are the basis of the fence

In general, the structure on which the corrugated sheet is attached consists of:

The main supporting elements that are installed at the corners of the site and on the sides of the gate. Typically, these pillars are slightly thicker, as they experience increased loads.
Intermediate support elements. Often, for economic reasons, they are chosen thinner because they are less loaded.
Raskosov. These elements are used to level the supports in cases where soil parameters do not allow concreting to be carried out with proper efficiency.
Horizontal joists. They are constructed from beams, or from small section profiles (30x30, 20x40 millimeters).

Fence design drawing

All elements must be rigidly connected to each other. For this purpose, both welding and mechanical connectors are used. How to choose the right supports, since the modern market provides products of various types?

A Question of Choice

Which supports are commonly used for corrugated sheet fences? The following types are widely used:

metal;
wooden;
profile;
reinforced concrete;
with brick pillars;
asbestos-cement.

Metal

This is the most common material for fence posts. Such supports are made from sections of round or profiled pipe with fairly thick walls (thickness of at least 2 millimeters, for tall structures - up to 3). The second option is more technically robust and looks much more presentable and modern. The length of the parts depends directly on the height of the fence. Depth into the soil - from a meter (on dense soils) to one and a half. The metal must be subjected to additional anti-corrosion treatment. And the upper segment of the support must be updated annually, covering it with protective compounds (for example, paint or varnish). The profile cut should be welded or an appropriate plug should be installed to prevent water from entering the product.

Profile posts for a fence made of corrugated sheets

Tree

This pole material is used in temporary structures. Wooden supports, of course, are inferior in their characteristics to those of metal or brick. But when it comes to saving, they are applicable quite often. Usually these are coniferous species: pine and spruce. The material itself is chosen with a sufficient cross-section and without large knots and cracks, even. Don’t forget to treat the supports with an antiseptic agent against pests. And lubricate the lower part with mastic to prevent moisture penetration.

Example of a base for a brick pillar

Concrete and brick

Asbestos cement pipes

Supports made from this material still hold a fairly strong position. After all, asbestos-cement pipes coated with a special compound can last for decades, requiring almost no attention - painting, processing! Low cost, resistance to humidity and pests - an excellent budget option. But each material has its drawbacks. Asbestos-cement products also have them. They are highly fragile, which makes them difficult to transport. The pipe is heavy and bulky, which makes installation difficult. You also need to prevent liquids from getting inside the product: when they freeze, they will expand and the column may split.

Asbestos cement pipes for supports

Pipe plug option from above

Work order

We start by marking the area to be fenced. We mark the perimeter of the area with a measuring cord (we also use wooden or metal pegs).
Next, let's start applying markings, actually under the supports. The optimal distance for fences made of corrugated board, according to many craftsmen, is 2.5-3 meters - from pillar to post. This is directly related to the nuance that the profile used for installing horizontal joists on the structure is six meters long. Thus, when marking spans of the specified length, it is easier to join the logs.

Drilling holes for supports

Using a drill (see photo), we make holes in the soil at the marked points. The diameter of the holes for the pillars should be at least one hundred millimeters larger than that of the supports.
We fill the drilled holes with crushed stone. Compact with a tamper. We place each element separately, aligning it with a plumb line/level.
Fill the gravel on top (up to half) and fill in the cement solution.
We fix the pillars with boards or braces. When the solution has completely hardened, remove the fixation. Only then can the logs be attached.

Be sure to watch the video: