Finishing ceilings in a house made of wooden beams. Wooden ceiling in the interior (19 photos): beautiful colors and design

The advantage of wooden ceilings over reinforced concrete slab undeniable in terms of environmental friendliness, sound insulation and heat-insulating properties of the room. Beautiful design a ceiling with a textured pattern will perfectly complement the interior of the house, where the wall cladding is also made of boards with the same cutting method, with a complete match in the density and type of wood. Wooden ceilings in the interior of a city apartment when used for wall decoration modern materials are not so clear.

Compatibility of wood with other materials

A wooden house with a clapboard ceiling is a common design. Regardless of whether the walls are covered with boards or have natural look Any type of log or beam, wooden ceilings are quite natural for the room. When covering walls with color, it is not at all necessary to give the ceiling the same shade.

With a reddish color scheme for the walls, the ceiling can be coated with impregnation or protective varnish with a yellowish tint.

Wooden ceiling and walls

Using wood with low humidity for walls, and boards with a natural level of humidity for ceilings, it is necessary to treat the surfaces with impregnations that preserve the natural color or give the wood a special shade. Otherwise, after a few years it will seem that the ceiling is made of material older than the walls of the house. This will be noticeable because the aging process of the wood will take place differently.

Wooden ceilings perfectly absorb steam, moisture, odors, whatever additional protection wood with natural humidity, in the kitchen will not only change color, but may also become deformed. Both of these defects can be easily eliminated using a plane and a grinder.

There is no way to get rid of the odors that the wood has absorbed. They can only be blocked with a varnish coating.

Such an attractive wood pattern with longitudinal lines is obtained by tangentially cutting the trunk. This means that the board has a high level of humidity and is susceptible to losing its original shape when drying. Ceilings from such boards can only be made for rooms with low humidity and constant temperature air. Making such ceilings at the dacha, which in winter time It's not heated, so in the spring you might be very disappointed in your decision.

Board and stone

In any interior, the ceiling should look more weightless than the walls, which is determined not by weight, but by the appearance of the material. Concrete blocks, brickwork, the appearance of natural stone in the design of walls will be an excellent basis for the use of wooden ceilings. Doesn't have to be used a natural stone and brick. It is quite possible to limit ourselves to imitations of these materials, which are presented in construction stores in the form of clinker facing tiles.

Wooden ceilings in a city apartment in the hallway or kitchen with similar cladding will be quite justified. Wood looks good in combination with plastered whitewashed walls. Interior textured paint is also suitable for decorating a room with wooden ceilings.

In the design of pubs, beer halls, night bars, stylized in antique style with use in the interior wooden shelving, cooperage items are often used in combination stone walls and floors with wooden ceilings.

To paint a wooden ceiling or not?

Wood does not go well with oily, smooth surfaces, even if the ceiling itself is covered with white paint. A painted wooden ceiling can be combined with a large number of materials, but there is no point in this, because most of the advantages that natural wood gives to a room will be securely hidden under a dense shell of paint.

The most best quality wood is that it maintains the level of humidity in the room, sacrificing its own appearance. By absorbing excess moisture from the air or giving it the missing moisture, the wood undergoes natural contraction or expansion, but this is not a problem for minor or short-term changes.

A wooden ceiling will suffer major damage due to prolonged exposure to water, and when the temperature drops to -10⁰ C or below, the boards may become covered with longitudinal cracks. The same deformation awaits them with prolonged exposure to heat and low air quality. It turns out that when using wooden ceilings in rooms where long periods of extreme heat or cold may occur, it is better to paint the ceiling to protect it from inevitable damage.

Room temperature is not capable of leading to such dramatic changes in the material, so in an apartment or residential building, it is better to use wooden ceilings without additional decoration. Only uncoated wood can fill a room with a unique woody aroma, having a calming effect on nervous system person, quality support favorable microclimate rooms, maintaining a constant level of humidity.

Wood and artificial materials

The desire to make a wooden ceiling in an apartment is fraught with several difficulties. One of them is the poor compatibility of the material with wallpaper and PVC panels, which are most often used to decorate walls, because these materials look, and in reality, are much lighter than wood. Here you need to play with color.

Light natural wood on the ceiling can complement walls paneled in a dark wood look or wallpaper based on a brick pattern.

In stores you can find panels made from wooden dies, designed to create a wooden ceiling suspended structure. Using them in combination with light-colored wall materials is just as impractical as boards. As they turn yellow over time, they look rather unsightly, and this makes the ceiling seem even lower.

Video gallery

Photo gallery

The ceiling of a wooden house is usually made in two main ways: by using beams (beams and boards between them) or by continuous rolling (from logs). Options for decorating it will vary, and the ceiling will have to be lathed from logs, and in the first case load-bearing structures there will be rafters and beams. The main task the ceiling decorator will want to make the ceiling more aesthetically pleasing, reliable, without causing damage unique properties breathable wood base.

Ceiling in a wooden house - simple and complex solutions

If the base of your ceiling allows you to qualitatively insulate the ceiling in the attic, sand it and varnish it from the inside, then this will be the most optimal solution its finishing. But very often during the construction process no attention is paid to the quality of ceiling boards and beams, so you have to resort to decorative coatings.

Looking for perfect solution Many people opt for wood-look laminate: in this case, the ceiling will look perfectly “wooden” and beautiful, especially if you install it in Spotlights. The main concern of the owner of the premises will only be to prevent moisture from penetrating under the frame, to which such a material, which is not very fond of dampness, such as laminate, is attached. And if the house does not settle, the structure may crack where the panels are fastened. But usually ceilings are decorated a couple of years after construction is completed wooden house.

Options for finishing the ceiling with wood

If the homeowner decides to finish the ceiling with panels, then let these be panels from solid wood from valuable tree species. The panels, consisting of a frieze, a plinth and the panel itself, are made according to individual parameters; all that remains is to install them correctly. This is not the most cheap way decoration of the room, but it's worth it! Such a ceiling also cannot get wet, so if you live in a two or three-story house, do not place plumbing fixtures above a room with such a beautiful and expensive ceiling. Natural wood after being heavily wet, it may crack when drying. Behind panels require special care and wiping only with compounds intended for these purposes.

Slat structures have decorative functions, in which slats of different formats and structures can be used, mounted between the beams, so as not to make the ceiling surface monotonous and boring. Each rail must be coated with antibacterial and fire-resistant impregnations. But slatted ceiling or a lining ceiling has a number of advantages compared to panel decor:

1. The environmental component of the design is preserved.
2. Possibility of choosing color and texture taking into account individual characteristics premises, its style, furniture.
3. This material not afraid of moisture.
4. It is easy to clean even without the use of detergents.
5. Possibility of installing communications inside the structure. When covering with laminate, communication components are also hidden behind the slats, but if the ceiling and walls are uneven, wires and other hidden components can be seen.

Beams, layers and other decorative elements for the ceiling in a wooden house

When covering a rolled-up ceiling with panels, false beams made of polyurethane can be used. Finishing made in contrast significantly enhances the aesthetic component of the interior.

At installation of lining, slats on the ceiling, made using the beam filing method, you can get creative with carving, burning and painting on wood. If the slats are monotonous, you can always find a way to decorate (or paint!) some fragments, and beams decorated with patterns generally look great.

The opportunity not to skimp on height and space makes available such ceiling design as several levels or making suspended ceilings. They can not be done throughout the entire space, leaving room for combinations with wood.

When talking about panels, we did not mention veneered MDF panels, perfectly imitating any type of wood. With proper waterproofing, if we are talking about one-story house and above the ceiling there is a roof, such panels will not warp, and with their help you can make interesting decorative solutions.

When decorating a living room in combination with any type of ceiling decor, stained glass windows can be used - from individual order designer ones to those made independently using self-adhesive film. Their interior lighting will add luxury.

Ceiling in a wooden house - old proven methods

One of the most standard solutions is a plasterboard ceiling. This material has both pros and cons. The advantages include its ability to breathe and mask communications, the disadvantages are the need for putty and painting, as well as its tendency to deform. To prevent the latter, drywall should be fixed to metal carcass. And this raises the question: will the material of your base withstand a metal structure?

Until recently, plaster was considered the only the right decision, but if the owner of the house does not know how to plaster, he will have to hire a master. The slightest flaws are clearly visible on the ceiling. Before applying the solution to the ceiling, a set of shingles is filled.

Another simple and economical way is to cover it with plywood with one side sanded. This type of work cannot be done alone; an assistant is required. If the plywood is of high quality, it will be enough to varnish it, choosing slats to mask the joints. If its surface is not aesthetically pleasing, it will have to be puttied and painted.

And, of course, it should be remembered that before starting work for any of the selected types of ceiling decoration, the base should be thoroughly impregnated with antiseptic impregnations, and a primer should be used before painting.

Ceiling in a wooden house - photo

Wooden houses on suburban areas are very popular today. The arrangement of such buildings includes many stages. One of the most important is the finishing of the ceiling, which significantly extends its service life and favorably emphasizes the interior of the room.

In this article we will look at the most common ceiling finishing options in wooden house.

Materials and their features

First of all Decoration Materials for the ceiling in a wooden house should be in harmony with the surrounding environment inside the building, including wooden walls.

Plaster

These days, there are many special mixtures that will help make the ceiling even, smooth and light.

But if their rather high price does not suit you, then you can turn to the method that our ancestors repeatedly used:

• We knock down a relief mesh from three-millimeter slats.
• We fix it with nails to the ceiling surface.

Tip: instead of slats, you can use a ready-made nylon frame network.
This will greatly reduce the volume and facilitate the necessary work.

• We dilute asbestos plaster with water in the percentage indicated on the packaging.
• Apply two layers of solution, allowing the previous one to dry.

Drywall

The fact is that it is very pliable when wet, like clay, and when it hardens, it takes on a solid, durable form. Which is ideal for creating various unusual designs.

Drywall also has the following qualities:

• Long service life. Compliance the right technology installation guarantees more than ten years of service.
• Ease of maintenance. It is enough to tint the fading areas.

Lining

Finishing the ceilings in a wooden house with clapboard harmonizes perfectly with the walls of the building.

In addition, it also has a solid list of advantages:

• Affordable price. You can always choose less expensive tree species if you are on a tight budget.
• Ecological purity due to natural origin.
• Low thermal conductivity, allowing you to retain heat inside the house.

Advice: installation of the lining allows for additional installation of insulating material under its surface.
This way you can further increase the heat-saving properties of the building.

• High level of sound insulation. It will help block out the noise of the rain.
• Long service life.

Tip: using clamps to secure products will allow you to completely hide the fasteners.

Veneered panels

This is very interesting materials for finishing the ceiling in a wooden house. The manufacturing technology of such panels is that a board made of cheap wood special technology glue a thin layer from 0.5 mm to 3 mm of expensive wood. So we get the same lining with all its inherent advantages, only looking much richer.

Array

This is what veneer is trying to imitate. Real expensive tree species. But while copying the appearance, a veneer panel can never compare with the quality of solid wood.

The instructions for installing it are similar to the lining, but the characteristics, of course, differ:

• Very high strength.
• Long service life, counting in decades.
• Solid aesthetic appearance.
• High price.

Plywood

Finishing the ceiling in a wooden house with plywood is more economical and simple option than using tongue and groove boards. Wood laminated board is made from quality veneer, which allows it to fit well into a woody environment and at the same time remain cheap.

Installation work with it goes faster thanks to large sizes and light weight, but they require an assistant.

Stretch ceiling

This amazing innovation is perfect for a house made of any material, but in the case of a log house there is additional nuance. Suspended ceiling due to its elasticity, it is not afraid of the inevitable shrinkage of the building. Therefore, it can be installed immediately after the construction of the building.

Pros:

• Beautiful appearance.
• Wide range of colors.

• Unique moisture resistance. If suddenly the roof of your house leaks, it will stretch, accumulating all the water, and will wait for maintenance personnel to pump out the liquid.

• High level of sound insulation.

Minuses:

• High price.
• Difficulty in carrying out installation work.

Plastic

If your budget is significantly limited, even using plywood is expensive, then turn to plastic. It is much cheaper and can have almost any color that imitates more expensive materials.

Quite practical option, which, of course, will not replace the reliability and warmth of wood, but can create its appearance.

Conclusion

To decorate and protect the ceiling in a wooden house, there are many finishing materials.

They are all different:

• complexity of installation;
• appearance;
• cost;
• and many other characteristics.

You can easily choose an option that meets the size of the budget allocated for finishing and your preferences.

The video in this article will introduce you to additional information. Good luck with your choice!

Wooden ceiling in the interior - relevant and stylish solution. Wood lends itself well to processing, which allows you to realize any extraordinary design ideas. Wooden ceiling coverings can be deliberately simple and even rough, or they can amaze with their luxury and sophistication. The material, taking into account the shape, color and style of specific finishing elements, will be appropriate in both classic and modern and even futuristic interiors. Therefore, today the wooden ceiling is again at the peak of its popularity. But it is not the only reason its relevance.

Features of a wooden ceiling

Its main advantage in the eyes of designers and consumers of their services is environmental friendliness and safety. Fed up with newfangled synthetic materials people are returning again to the “well forgotten”, but such a solid and proven “old”. Moreover, modern means for wood processing, they allow you to forget about such troubles as accidental fire, bark beetle attacks, excessive moisture saturation and rotting. The tree is saturated essential oils, famous for their healing properties. Once in the atmosphere of the room, their components have a beneficial effect on the health of the inhabitants of the house.

The natural ability of the material to absorb excess moisture and release it back during the dry period ensures the maintenance optimal microclimate. No less attractive characteristics of wood is its ability to heat and sound insulate. And thanks to the long service life wood covering more profitable than most known finishing options.

Types of wooden ceilings

The variety of materials for constructing wood ceiling coverings is impressive. We list the main types of finishes in this category, presented:

Wooden panels

The main advantage of the panels is ease of installation. This work can be done with your own hands. Individual fragments are attached to the sheathing with nails or clamps, or fixed directly to the ceiling with glue. If replacement is necessary, the ceiling elements can be easily removed. There is no need to dismantle the entire coating.

The shape of the products is varied. They are produced in the form of slats, sheets and square typesetting elements. The panels allow you to perfectly disguise electrical wiring. Therefore, all possible lighting scenarios are allowed. There is also no difficulty in installing absolutely any lamps into a plank ceiling.

Based on the production method, there are two main groups of wooden panels. These are the products:

• from an array of valuable rocks. The wood used for production is oak, maple, beech, and alder. To emphasize the natural beauty of natural boards, the panels are treated with special mastics. They make natural fibers brighter and more distinct, due to which the natural texture of wood is clearly drawn and becomes more picturesque and impressive;
• from several layers joined together. The upper decorative layer is made of valuable species, and the lower layers are made of coniferous trees.

The ceilings in the living rooms of luxury houses are often decorated with luxurious panels with beautiful embossing and gilded carvings. They are coated with compounds that give an expressive glossy shine and shimmer.

Lining

The most common area of ​​application of the material is finishing steam rooms, terraces, balconies, country houses. But nothing prevents you from making a ceiling covering in your apartment from it - if the designer’s idea requires it. Initially untreated boards can be impregnated with stain desired color, paint or simply varnish to preserve the natural grain pattern of the wood.

There are several categories of lining, depending on its quality:

To avoid installation problems, it is very important when choosing a lining to carefully inspect the tongue-and-groove joints for integrity.

Cladding slabs

Products are formed by combining crushed wood with an adhesive component.

Product options:

Plywood

Deciding on the material for ceiling covering It rarely occurs to anyone to use plywood for these purposes. And completely in vain. Using this material you can create a beautiful, and most importantly unusual and exclusive ceiling.

Plywood is a material consisting of several layers of veneer, each of which is applied perpendicular to the previous one. First, the core is made from coniferous species. Subsequently, maple, birch or alder veneer is glued onto it on both sides. For the elite variety, beech is used.

The material differs in the following indicators:

• the number of layers may vary. They produce three-, five-layer, and multi-layer versions of the material;
• according to manufacturing materials;
• in terms of moisture resistance - standard, with increased protection against moisture, laminated with high level sustainability;
• type of processing - with a polished surface and untreated.

Unsanded elements are perfect for country house or outbuilding. If you plan to use plywood to finish the ceiling of a corridor in a private house or the living room of a mansion, you should give preference to polished elite class plates. Picturesque panels with colorful patterns will become a bright and unique decoration of the room.

Wood wallpaper

They help to recreate a special atmosphere of natural comfort at home. There are several types of materials in this category. They are divided into groups depending on the raw material and the method of its processing.

Types of wallpaper with a wooden surface:

• Panels made from narrow wooden planks, the thickness of which does not exceed 2 cm. Their cost depends on the value of the wood used;
• Veneered – thin layer natural wood 3 mm thick, glued to paper base. May have a carved and inlaid decorative surface;

• Cork - a coating of crushed cork tree bark is applied to paper. In order to protect the material from odors and exposure to chemicals, the top is opened thin layer wax. Wallpaper is produced in the form of slabs and rolls of 10 m. Roll products are not impregnated and can be painted in any color;
• Materials made from thermally treated wood. Technological process provides raw materials with improved qualities - their resistance to fire, mechanical damage, and moisture increases. TMD wallpaper belongs to the washable category. A variety of tree species are used in their production. For finished products Characteristic marble color.

Rolled materials on a paper or non-woven backing are a worthy alternative to expensive typesetting elements. They are fixed with glue directly to the ceiling. There is no need to build a sheathing or spend money on additional materials.

The base on which the wallpaper will be pasted must be level, so if there are large differences and deep cracks in the ceiling, they must be eliminated with plaster.

Ceiling fillet

The final “chord” when arranging a wooden ceiling is undoubtedly the fillet. This is the name of the ceiling plinth, which carries several functions at once. He helps:

• hide irregularities and defects at the junction of the main covering with the wall;
• create an elegant frame. The fillet outlines the contour of the ceiling, placing it in a spectacular frame, like a painting, and gives it a complete and expressive look;
• close the cracks, hide the wiring and protruding elements of the sheathing.

For each interior solution, you can choose the appropriate baguettes. For classics - pompous - gilded, carved, for modern version– laconic, seasoned, not flashy.

False beams

Wooden hollow beams give the room a special touch. They bring rustic simplicity and comfort to city apartments country house. Thanks to them, it is possible to solve several design problems at once:

• visually “pull back” the ceiling;
• “pull” the room in the direction of the beams;
• zone the room;
• create lines that clearly contrast with the background of the ceiling, harmonizing with the plinth, platbands and other elements of the furnishings;
• place electrical wiring in the cavities, fix lamps and develop a non-trivial lighting scenario.

The varied shapes of the hollow beams make it possible to ideally conceal pipes and cables.

When making false beams from natural wood with your own hands, you should take into account that during the drying process, the seam connecting the individual slats may separate and become noticeable.

Wood colors

When choosing the color of a wooden ceiling, you should focus on the overall color scheme premises. The coating must fit into the interior and look harmonious in it. Finishing in dark shades is appropriate in good lighting in a room with high ceilings. In the opposite situation, it is better to choose light materials that will visually push back the ceiling and make it airy and unobtrusive.

When deciding on a color, it should be taken into account that when exposed to sunlight wooden elements may darken.

What styles would be appropriate?

Wooden ceiling decoration is ideal for houses designed in a rustic spirit; it is no less relevant for classics. But specifically for country styles, “ Hunting lodge"and chalets like ceilings are an integral and required element. The first two welcome rough, unprocessed textures, giving the entire ensemble the most natural look.

A large number of beams under the roof are characteristic of the chalet style, which has absorbed the features of a rustic Swiss house. But if desired, wooden elements can harmoniously fit into almost every room. It all depends on the specific materials and the imagination of the design author.

Wooden ceilings will add extraordinary comfort and originality to any home. In combination with appropriate decorative elements, this coating will look great.

The construction of wooden houses in suburban areas is becoming increasingly popular. The natural beauty of wood, aesthetically attractive appearance, ease of installation of the structure are just a few of the advantages for which wooden houses are so valued. However, in addition to the construction of housing, its finishing will be required, consisting of several stages, one of which is the design of the ceiling surface.

Ceilings in wooden houses can be made from various materials, but we must not forget that each of them must fit harmoniously into the overall style of the room and continue it.

Finishing the ceiling in a wooden house: design methods

Ceilings in wooden houses are lightweight structures based on beam floors. Due to the minimal load they place on general structure, such ceiling surfaces are characterized by a long service life and reliability. The materials used for cladding ceilings can be: various options. But first it is necessary to understand the main features associated with the construction of such houses.

First of all, the natural shrinkage of the log house, which in the future can lead to deformation of the ceiling surface. It is this factor that should be taken as a starting point when deciding how to cover the ceiling of a wooden house inside. It is better if natural materials are used for such work, providing suitable humidity air and the required level of ventilation. For example, the same tree. But you can use other ceiling coverings depending on your financial capabilities and installation method.

You can sew up a ceiling in a wooden house:

• Clapboard.
• Plywood.
• PVC panels.

And yet, how to decide what to decorate the ceilings in a wooden house? From what designer style is supposed to be indoors, you should start when choosing materials for finishing the ceiling surface.

DIY ceiling in a wooden house: preparing the surface for work

After the question of how to finish the ceiling surface has been resolved, it is necessary to prepare it for the main process. Regardless of the chosen option, installation of the material should begin only after high-quality treatment of the main ceiling with antiseptics. A primer will be required and wooden elements, if they are chosen as the basis for the design.

In the case where the base surface is roof structure elements treated with preparations during the construction stage, work on the installation of thermal insulation materials can immediately begin. This can be a material produced in the form of slabs or rolls, laid between beams and covered with sheathing. Thermal insulation is necessary to prevent heat from escaping from the room and to protect the room from extraneous sounds, if there is an upper floor.

As a thermal insulation material to insulate ceilings in a wooden house, you can use:

• Mineral wool.
• Expanded polystyrene.
• Felt or jute.
• Fibrolite.
• Reed slabs, etc.

If you decide to finish the ceiling in a wooden house yourself, you need to prepare in advance necessary tools: tape measure, level, electric drill and screwdriver, hacksaw, construction knife, finishing materials.

Important! Ceiling installation can begin only after natural shrinkage of the main residential structure.

The gap between the mounted ceiling and wooden walls in this case, it must be at least 5 mm, since air humidity and temperature fluctuations affect changes in the dimensions of the base material, which can lead to deformation of the ceiling covering. You can hide the cracks using ceiling skirting boards or galette depending on the option chosen.

How to make a ceiling in a wooden house: installation of various types of coatings

1. Wooden lining

• Good heat and sound insulation.
• Concealment of visible defects formed during the construction phase.
• No preliminary grinding or leveling of the ceiling surface is required.
• Long service life of the material if the installation phase is carried out high-quality processing linings with protective compounds.

A lining ceiling will visually change the size of the room when the right way laying the material. If installation is carried out in parallel narrow wall, this will expand the room. Laying the lining diagonally will enliven the interior.

Installation of the lining is carried out on the sheathing.

Important point! For residential rooms will do option “lining - wooden sheathing”. Where high humidity It is better to use slats made of metal or plastic in combination with the lining.

The step between the lathing slats should be at least 50 cm, the location of the bars should be strictly horizontal, forming a single plane. Before installing the lining, it is necessary to provide locations for electrical wiring for lighting fixtures.

The ceiling is covered with clapboard perpendicular to the slats. The first plank, on which the tenon is pre-cut, is attached with a slight indentation from the wall (the required gap is 5 mm), after which it is screwed to the sheathing using self-tapping screws from the front of the material. The caps can be covered with a plinth.

Next, a ridge is inserted into the groove of the first board. The elements are fixed to each other with light blows of a hammer through a piece wooden board so as not to damage the material. The protrusions of the groove are attached to the sheathing with metal clips and nails. The entire wooden ceiling made of clapboard is installed using this type.

For finishing, eurolining can be used, which differs from simple lining in its improved lock design and high physical properties.

Plywood ceilings are not often used as a material when necessary in a private wooden house.

And in vain. By finishing ceilings with plywood you can achieve original design and a flat surface.

Plywood is distinguished by the following parameters:

• Moisture resistance. Coating with a layer of laminate makes the sheets durable.
• Grades. There are five types of plywood in total, each of which can be used for cladding the ceiling surface.
• Processing methods: untreated, sanded on one or both sides.
• Appearance – decoration with plastic, patterns or “natural wood”.

To the rough ceiling to be finished, you need to install a sheathing of wooden slats or aluminum profile. You can attach plywood to the sheathing using nails or self-tapping screws. We will hide the joints under putty or sew them with a wooden strip.

They can also be used to decorate a ceiling with wooden beams. Such suspended ceilings will help out if the rough surface is severely deformed or there are noticeable flaws on it. The result at the end of the work will be good and even.

There are two methods of installing a plasterboard ceiling according to the mounting methods:

On a wooden frame. This option is ideal for creating a regular single-level ceiling. At the same time, the wood for the frame must be of very high quality.

You must proceed as follows:

• Determine the most bottom corner room and, stepping back 5 cm from it, draw a horizontal line along the perimeter of the room.
• Then attach it in a circle wooden blocks and slats along the entire length of the room. The distance between them should be 80 cm.
• After this, fix the supporting strips across them at a distance of 50 cm. Drywall will be attached to them in the future.
• On a metal frame.

This method is reliable and involves the following sequence of actions:

• The ceiling is marked according to the first method.
• Metal guides are attached horizontally to self-tapping screws or dowels.
• Next, the profile is fastened at a distance of 40 cm from each other perpendicular to the guides.
• The structure is fixed with self-tapping screws.
• To increase the rigidity of the sheathing, hangers are used.

The drywall is fixed to the frame with self-tapping screws in increments of 25 cm. The heads of the screws need to be slightly “recessed” into the surface of the sheets. In the future, they can be covered with putty.

They represent non-standard variations in the finishing of the ceiling surface in houses made of log house. Budgetary, but nevertheless beautiful ceilings, ideal for a wooden house. Ready material polyvinyl chloride does not require further painting or processing. The main thing is to choose the right color.

Initially, a frame is installed from metal profile or wooden slats in increments of 40-50 cm, which are screwed to the beam surface. Next is mounted starting profile along the entire perimeter of the room, where they are then inserted PVC boards. Each ceiling board made of polyvinyl chloride is fixed with self-tapping screws to the sides of the frame rail. Finishing consists in decorating the structure with ceiling plinths.

To give the ceiling originality, any of the selected materials can be decorated with wallpaper, curly moldings, stucco, small wooden slats or paint individual parts.

Installation of an insulated ceiling with visible beams video instructions