Aquastop waterproofing: application features, consumption, price. Waterproofing mixture AQUASTOP Aquastop waterproofing liquid

Waterproofing is a very necessary process at various stages of construction. However, it is not always possible to complete such work. Purchasing a secondary home with no property waterproofing layer or a recently purchased new building not meeting certain standards - there can be many reasons, but the problem must be corrected immediately. For this purpose, effective modern materials, different high degree adhesion to the surface and maximum protective characteristics.

The most effective is the Aquastop system - waterproofing, consisting of three various materials, providing reliable and quick protection of substrates exposed to moisture. Its components (both in combination and separately) are successfully used at many construction sites.

There are many materials for protecting surfaces from moisture, but this waterproofing compares favorably with them:

• it works effectively on wet and leaking surfaces;
• retains all properties even under water and in underground space;
• does not require additional work related to pumping out or removing excess moisture;
• is able to harden quickly, even under pressure;
• withstands significant pressure (similar to that generated in a 70-meter water column);
• no complications during the application process: simple stage-by-stage work without the use of special equipment;
• high quality typical of original German products.

Preparation instructions and application diagram

In order for the waterproofing layer to serve for a long time, it is necessary to adhere to a certain sequence of application of layers and follow a special technology.

So, first you need to apply a special powder called “Puder-Ex” to the base. In contact with water, it hardens very quickly (literally in seconds), forming reliable adhesion to brick, stone and, of course, concrete surfaces. With its help, you can eliminate all damage that contributes to leakage and at the same time strengthen it.

Thus, still on preparatory stage any leak is eliminated, and the applied material acquires:

1. high water resistance;
2. resistance to aggressive environment(including various chemical compounds) and low temperatures;
3. strength.

When starting work, you should wear rubber gloves with a smooth surface. Before application, the product is not dissolved or mixed with other substances. All that is required is to take a small amount of building powder, then squeeze it in your palm for a few seconds and fix it with a quick movement. The mass should cover the hole and some area around it. Without removing your hand, you should hold the material for 10 seconds - during this time it is saturated with water, forms a strong bond with the base and quickly hardens.

All small damaged areas are treated in this way. If drops of moisture are constantly released on a significant part of the base, you must proceed as follows: a small amount of powder is rubbed over the designated area with the back of the hand in strictly vertical movements (from top to bottom and vice versa). This will allow the problem area to be treated more evenly and prepare it for the application of the main complex of materials.

There are also cases when the defect is so large that it is simply impossible to eliminate it in one go. In this case, the hole is closed gradually, using the first method of applying a waterproofing compound (for small holes). By repeating the above procedure many times, maintaining a ten-second interval each time, you can significantly reduce the location of the leak, and then completely eliminate it.

Installation of waterproofing dowels

During pre-treatment reinforced concrete and concrete foundations All seams of the structure should be processed properly by filling them out and installing special dowels.

This point is especially important if work is carried out in basements and underground areas, as well as on the foundations of buildings. Waterproofing dowels are made of durable rubber based on synthetic rubber, which significantly increases their service life.

Step-by-step installation

When preparatory work completed, apply five-layer waterproofing:

1. Sealing layer. Using a brush, a pre-prepared solution of special slurry (cement with a certain set of reagents of inorganic origin) is evenly distributed over the wet base. To obtain a homogeneous solution, the dry mixture is diluted in water and stirred vigorously without the use of equipment. When the mass becomes plastic, it can be applied. However, this should only be done within the temperature range from +5° C to +30° C. Each portion of the mixture should be made small, because it hardens quickly. For comparison: an experienced builder similar works can cover a maximum of two with this composition at a time square meters grounds.
2. Consolidation. Without waiting for the applied mixture to dry completely, a special powder-like fixative is quickly rubbed into it.
3. Hardening. Application of insulating silicicate. This will increase the strength of previously applied layers. Tools for work: brush or suitable brush.
4. Sealing. Everything is immediately covered with a special sludge, and then there is a twenty-minute break.
5. The final coating is also carried out with a solution of special slurry. This is the finishing layer: plaster will be applied to it (if the base is a ceiling/walls) or a screed will be installed (if it is a floor). Subsequent work can begin no earlier than 24 hours later.

If everything is done in accordance with the technology, Aquastop waterproofing will be durable and reliable. Despite enough thin layer(only about 3 mm), the system will withstand heavy loads and adverse environmental influences.

However, the secret to the success of this system is not only in the combination of materials. Speed ​​of work completion, good experience and the corresponding skill of the performer also have a significant impact on the quality of the future coating. These are good reasons to entrust such a difficult job to people who can handle it with dignity - experienced craftsmen with experience.

Reliable waterproofing is required at all stages construction work- from building the foundation to protecting façade structures and finishing damp interior spaces. The term "aquastop" is used in relation to the whole system water protection various surfaces, although it was first used in 1993 by the Swedish manufacturer Eskaro for its water-repellent primer. Today, a whole line of moisture insulators is produced under the Autostop brand.

Purpose

Aquastop protects foundations, plinths, balconies, loggias and terraces, floors and walls of swimming pools from moisture. This primer is treated before finishing floors, walls and ceilings of kitchens, bathrooms and shower rooms, laundries - rooms with high humidity.

Giving water-repellent properties to the surface of any materials used in the construction of structures and finishing works inside and outside - the main purpose of using Aquastop coating. It is applied to:

• brick;
• concrete;
• porous aerated concrete;
• cement-sand and lime plaster;
• gypsum;
• drywall.

The ability to withstand moisture is used to modify mortars and concretes based on cement-based binder mixtures. Adding Aquastop gives ready mixture, in addition to water-repellent qualities, others beneficial features: high adhesion, ductility, abrasion resistance, resistance to alkalis and petroleum products.

Release form

The main feature of Aquastop compositions is releasing them in the form of concentrates, requiring the addition of 5 to 10 liters of water per liter of primer. This allows you to use primers and mastics of the desired saturation, save space on the construction site, and reduce transportation costs.

If you do not dilute the composition when applying waterproofing, you can get a “slippery” impermeable film, which reduces the adhesive and “breathable” qualities of the coating.

The Aquastop line includes compositions with specific properties:

Application methods and operating procedures

Proper use of Aquastop begins with choosing the type of primer or mastic depending on the application. It is necessary to take into account the frost resistance of the composition when used for facade or interior work. The amount of water for dilution when working with concentrate is selected based on the quality of the primed surface and the materials used in subsequent finishing.

The primer is applied with a brush, roller or spray. Aquastop Hydro mastic, depending on the desired viscosity and thickness, is applied with a brush or a structured roller; if particularly strong waterproofing is needed, the mastic is leveled with a spatula.

It is important to prepare the surface of the slab for coating it with Aquastop. The presence of frames and supporting structures for the floor, as well as old cladding, will worsen the waterproofing properties of the coating. Just like garbage and dust. Should patch up plaster mortar or putty cracks, chips and depressions. Their presence will lead to moisture penetration and overconsumption of Aquastop.

Following the manufacturer's recommendations is the key reliable waterproofing. Thus, according to the manufacturer’s instructions, work should be carried out at an ambient temperature of +10 to +30 ⁰ C. The concentrate should also be diluted need expert advice, focusing on the condition of the surface. Usually water is added in a ratio of 1:3 or 1:5.

The approximate consumption of the finished Aquastop waterproofing composition is 125 g/m2. On problem areas- seams, joints of structures and communication outlets, soil consumption increase. Waterproofing begins with thorough treatment of such areas, after moistening the surface with a spray bottle.

Then the entire surface is waterproofed in several steps. It is not necessary to wait for the previous layer to dry completely, you just need to let it set. If the protective primer is applied with a roller, it is better to use a “coat” with short pile, rolling out the composition rather than smearing it.

Typically the waterproofing step is followed by thermal insulation work. Deep penetration Aquastop into the treated surface increases the mechanical resistance of the coating, but when choosing a method of insulation, you should choose methods without compromising the integrity of the waterproof layer.

Protection of a balcony or loggia from moisture penetration can be achieved using various modern methods. The choice of waterproofing depends on the conditions of use and, of course, the material of the structure that needs protection. Universal waterproofing Aquastop, being an advanced product on the construction market, will allow you to approach waterproofing issues in a comprehensive manner. According to professionals, this system has no analogues.

What is Aquastop?

This is a specific material used to obtain a reliable and durable water-repellent coating. Aquastop is used for finishing different reasons: from brick, concrete, plaster, cement, aerated concrete, gypsum and other materials. This type of waterproofing can be used for priming porous surfaces and moisture-sensitive materials.

Aquastop is a universal product line containing a set of high-quality water-dispersion primers that protect the room from moisture. A similar task is relevant for finishing a balcony or loggia with insulation. To provide a room with comprehensive water protection, it is necessary to use 3 types of dry mixture, each of which does its own job:

• Specific concrete slurry, consisting of several components, with the addition of inorganic chemicals. substances.
• Fixative powder, in the form of a dry mixture. Its purpose: increases the reliability of the surface being treated and serves as an excellent sealant.
• Silicon-based waterproofing or otherwise silicone insulation, which does not contain solvents. Main functions: sealing micropores obtained after surface treatment with fixative powder.

Tip: If you need to seal the seams between panels, as well as the wall and foundation, use a unique Aquastop waterproofing dowel. Made from high-strength rubber, it also effectively holds a large influx of water.

Scope of application Aquastop: internal and exterior decoration residential, office and production premises; used in the kitchen area and bathroom, laundry room and other rooms that have a fairly high degree of humidity.

Waterproofing characteristics

• Products in various designs: waterstop, specific profiles, sealing complex expansion joints, injection system, AquaStop waterproofing and others. The latter, for example, is multi-format coating waterproofing , forming a reliable water-repellent film on the surface.
• The composition of waterproofing products allows them to be used in difficult areas of the structure: for example, in places that are most susceptible to displacement loads.
• Any base can be primed: concrete, plaster, stone, and so on.
• Does not contain toxic components.
• Purchased in the form of a concentrate and traditional composition.
• Some products in the series include components that protect the treated base from rot.

Waterproofing Aquastop Perfekta (Perfecta)- This mortar to create a hard waterproof coating (waterproofing layer) on various reasons; used for building foundations, facades, plinths, basements, balconies, terraces.

The coating is highly waterproof and waterproof, withstands high mechanical loads, and is resistant to alkali salts. We especially note that the price of Aquastop is quite affordable compared to competitive brands.

The material is used for waterproofing building foundations, facades, plinths, basements, balconies, terraces, indoor pools, water tanks, walls and floors in wet areas. The material is designed to create a hard, waterproof coating. Buy waterproofing at favorable price only available from an official partner.

Key properties

How to apply Aquastop waterproofing?

Perfekta Aquastop waterproofing is easy to apply. This is done using one of the tools: a brush, trowel or spatula on bases whose temperature is in the range from +5 to +30 degrees.

If you decide to work with a brush, then for the desired effect the waterproofing mixture is applied in three layers, with each layer applied at an angle of 90 degrees to the previous one. Each subsequent layer is applied after approximately eighteen hours. The thickness of the coating should be about 3-4 mm.

If it is more convenient for you to work with a trowel or spatula, then you can apply the waterproofing mixture in two layers, and it is recommended to apply the first layer with a brush.

In addition, in order to achieve greater water resistance, it is best to apply Aquastop with a spatula (or trowel), in this case the indicator will reach the W20 level, which means the ability to withstand water pressure of 20 atmospheres.

When applying the waterproofing mixture with a brush, the waterproof rating will not exceed level W8 (8 atmospheres).

Subsequent work, such as plastering, laying tiles or porcelain stoneware, creating self-leveling floors, screeds, is recommended to be carried out no earlier than three days later. At the same time, for three days it is necessary to avoid direct contact with the applied waterproofing (waterproofing mixture). sun rays, natural precipitation and exposure low temperatures(frost).

What is the mixture consumption?

The average consumption of Perfekta Aquastop dry mixture is about 4 kg per 1 sq.m.

Scope of application

1. Waterproofing of building foundations, facades, plinths, basements, balconies, terraces, indoor pools, water tanks, walls and floors in wet areas;
2. Installation of horizontal cut-offs;
3. Creation of a waterproof coating on traditional substrates: concrete, brickwork, cement strainer, plaster.

Coating rigid waterproofing mixture based on cement, fractionated sand and hydrophobic polymer, for the protection of basements, basements, swimming pools, bathrooms, blind areas, foundations, etc. from water penetration.

Preparing the base:

The base on which it is applied waterproofing coating, cleaned from dust and dirt, loose particles, oil, paints, etc. manually or mechanically (using high-pressure water, sandblasting). Defective concrete is healed repair crew. The prepared base must be moistened before applying the main coating.

Preparation of the solution:

Pour the mixture into a container with clean water(at the rate of 6.0-6.5 liters of water per 25 kg of mixture) and mix mechanized way until smooth (about 2-3 minutes). Let the solution sit for 2 minutes, then stir for 1-2 minutes.

The prepared portion of the solution is used for its intended purpose within 40 minutes (after adding the mixture to the water). If the solution loses its mobility, it is permissible to re-mix without adding water.

Application:

The prepared solution is applied to the prepared surface to be treated using a hard brush, brush, spatula or appropriate spray equipment in one layer. If necessary, apply a second layer, strictly in a perpendicular direction, while the first is still “fresh”. During the entire hardening period, the freshly applied solution must be protected from direct sunlight, rain, wind, etc. Mixture consumption: About 4-5 kg/m2 when applied in two layers with a total thickness of 2-3 mm.

Packaging and storage

Kraft paper bags 25 kg. The shelf life in a dry place and original packaging is 12 months from the production date indicated on the packaging.

Security measures

Do not let the dry mixture get into your eyes. In case of contact, rinse the affected area thoroughly. running water, if necessary, consult a doctor. Wear goggles and protective clothing when working.