How to drill a glass jar at home. How to make a hole in a glass bottle with your own hands How to make a hole in the bottom of a glass bottle

You will need

• - air gun;
• - drill with a diamond or hardened steel drill;
• - turpentine;
• - sulfuric acid;
• - water;
• - sand or clay;
• - a template made of wood, foam plastic, glass, metal or other material;
• - emery powder.

Instructions

Most quick way: Take with a well-charged cylinder. Stand a few meters away, aim carefully and shoot at the bottle. The ejected ball will pierce right through the bottle without breaking it. Please note that there will be two holes, and of a rather small diameter.

To drill in bottle hole the desired diameter, first prepare a device for securely fixing the dishes, for example, a box in which they will sit tightly. Take a diamond drill bit for ceramics and drill very carefully, without pressing. Be sure to consider the cooling system. This can be constantly supplied water (an assistant will be needed here) or a specially prepared cooler. To make it, make a template out of wood, foam or other material by drilling into it hole the desired diameter, and attach it with wax to bottle. Fill the hole with sanding powder (this can be obtained from sandpaper or abrasive wheel), mixed with turpentine.

To drill hole in glass bottle steel drill, before use, heat it until white and soak it in sulfuric acid.

To drill hole large diameter, take a tube made of non-ferrous metal (aluminum, brass, copper, bronze) 2.5-5 cm long and use it as a drill. Attach a circle made of foam plastic, glass, wood, metal or other material of the required diameter to the glass; the tube will rest against it when drilling. Pour into open end tubes with emery cloth moistened with water and drill slowly, at low speeds. Make sure that the sanding paste is always between the edges of the tube and the glass.

If you want to avoid drilling, use clay or fine sand. Thoroughly wash the surface from grease and dirt using acetone, alcohol or gasoline. Pour wet sand or clay, mixed to a dough-like state, in the form of a slide about 10 mm high. Make a funnel with a stick or other tool, and the diameter of the translucent glass inside the hole should correspond to the diameter of the desired hole. Melt lead, tin or other solder in a metal jar and pour it into the resulting hole. The hole will have smooth edges, but remember that this method is suitable for glass no thicker than 3 mm.

How to drill a glass bottle with your own hands. Very original lamps are made from shaped and colored glass drink bottles. Several attempts made at one time to drill bottles ended in failure. The methods for drilling glass were some exotic ones and usually ended with a long crack in the glass from the point of drilling. But if I used a special glass drill, everything worked out. To drill a beautiful rectangular bottle of a good drink, a drill with a carbide insert was purchased (~ 60 rubles).

Features of drilling a glass bottle

1. Direct the drill fixed in the electric drill strictly perpendicularly to the point of drilling the bottle and, with slight pressure, wait for the first glass crumbs to appear.

2. There is no need to drill at maximum speed, the drill is afraid of overheating.

3. Every 20-25 seconds, stop drilling and remove glass chips. At the same time, the drill tip will cool down.

4. When the tip of the drill passes through the thickness of the glass, the drilling sound will change slightly and the drill feed (pressure) should be reduced to a minimum.

5. After drilling through the thickness of the glass, rinse the bottle in running water.

6. When drilling, it is better to follow safety precautions - work with gloves, goggles and respiratory protection.

In this way, several glass bottles were successfully drilled with my own hands, from which they were made with power from a 220 volt network.

I am often asked HOW to make a hole in a bottle to create a lamp base.
Here is a short master class on how I do it.

You will need :

* Wine bottle with wide neck and screw cap
* E14 lamp socket
* electric cord with switch
* Matte ENERGY-SAVING light bulb with E14 base, power 7-8W
* Perk for metal
* Screwdriver
* Drill for glass and ceramics
* Diamond needle file (recommendation forcon )
* Jar of water
* Scissors
* Glue gun
* Safety glasses (recommendation ntl )
* Protective mask

I am often asked how to make a hole for a cord in a bottle.
To do this, you need to purchase a special drill for glass and ceramics at a hardware store. For the Hole, I use a #6 or #8 feather drill bit.
You will also need a drill or screwdriver.
Here are a few photos of the materials you will need.

Operating procedure :
Take the bottle and wrap it around the area where the hole will be located. masking tape 2-3 times.

Mark the drilling location with a cross. Please note that bottles have seams, it is best not to drill directly into the seam of the bottle. Move the drilling location 1-2 cm.

We begin the drilling process. We dip the drill in the water and try to hold the drill very evenly at medium speed and begin to drill. The most important thing is not to put pressure on the bottle under any circumstances. Act confidently, but not harshly.

Drilling will take 10-15 minutes. The pen drill will seem to scratch out the glass.

While drilling, regularly lower the drill into water and drip onto the drilling site.

After the drill has gone through, carefully drill the hole for some time, making light rotational movements. This will make the cut of the hole smoother.

Use a regular file or coarse sandpaper to sand the edge of the cut.
This is what you should get:

Now take the cord with the switch

And we pass it through the hole, pulling it up.

I would like to immediately make a reservation that if you plan to decorate a bottle, then the order of work should be as follows:
First you make a hole, then you decorate the bottle, then you put everything together.

Now a few words about light bulb sockets.
I use light bulb sockets with a base size of E14. A regular light bulb has a power of 40W or an energy-saving one 7-8W. I prefer energy-saving lamps; they do not heat up the lampshade.
There are two types of cartridges: “without a skirt” and with a “skirt”. We need cartridges with a skirt and a fastening ring.

These are NOT the correct cartridges, WITHOUT a “skirt”

The CORRECT cartridge with a “skirt” and a ring.

Now we take a bottle cap (I wasn’t free, so I took a regular cap as an example).

We make a mark on it with the middle. We measure the diameter of the cartridge and select the appropriate perk for metal.

What to do if there are no metal perks? I suggest this method: Punch holes in a circle with an awl, often and close to each other, and then saw through with utility scissors or a needle file.

The entire hole is ready and we begin to put everything together.
We bring the cord through the neck of the bottle.
We connect the cord and the cartridge.
We pass the cartridge through the hole in the lid. The lower "skirt" of the cartridge will prevent the lid from falling off. For reliability, we drip some glue from the gun around the skirt and attach the lid to the skirt.

Close the bottle with a lid. All our cartridges are securely fastened.
Using the upper clamping ring, you subsequently attach the lampshade to the socket.

Attention, there are situations when the lampshade mount is larger in diameter than the fastening ring. What to do? It is necessary to make a gasket that equalizes the diameter of the lampshade and the diameter of the fastening ring.

Your imagination for decorating bottles and lampshades remains in your hands! Create and you will definitely succeed!

When making a homemade shade for a lamp or candle, it may be necessary to drill a central hole in the glass bulb. You may need to make a hole in the glass for other purposes. You can drill anything, glass jars, bottles or other containers, beads, glass doors.

A diamond drill (drill) is suitable for drilling holes of small diameter.

A crown is a special circular drill; unlike a drill, it drills around the circumference without touching the central area. Thanks to this, the crown is suitable for drilling large-diameter holes.

We cover the drilling area with adhesive tape crosswise to reduce glass chipping. It is advisable to tape the inside as well, so the edges of the hole will be smoother and you won’t have to sand them for a long time.

Mark the center and start drilling. If you use special crowns, they have a spring-loaded guide drill in the center.

To use such a tool, you first need to drill out the center with a drill, and then continue drilling with a hole saw.

In other crowns there may not be a center. Of course you can drill, but it will be more difficult to start in the right place. It is more convenient to do this on a stationary drilling machine, but in a pinch, a screwdriver will do.

I mentioned the screwdriver for one reason. When working with glass, you need to add water to the drilling point. Otherwise, the glass will crumble a lot and small fragments will create problems for you. Close to the topic, the article is a homemade drilling machine.

In addition, the tool must work at low speed; rushing here will not lead to anything good.

Therefore, using a screwdriver is more convenient and, most importantly, safer.

Take your time, do not press too hard on the drill, as you may break the product.

After drilling is completed, the edges are treated with sandpaper.

However, if you used water and sealed the drilling site with adhesive tape, then as a rule the hole will turn out with smooth edges.

To hang a decorative lampshade, insert a rope into the hole and tie a knot inside.

Tools

If it is necessary to drill glass surfaces, many prefer to entrust this task to professionals, contact special services, they waste money, and most importantly time. We’ll find out how to drill glass at home and what you can use to drill glass.

Types and features of glass

Glass formation occurs during supercooling of a melt from several components, and the speed this process quite high and the crystallization process does not have time to complete.

Glass is a fragile material that is often used for human needs. Glass is formed when quite high temperature from 200 to 2500 degrees. Not all glasses are transparent; this property is not general characteristic of this material.

In relation to the main material used during glass production, glasses are distinguished:

Depending on the type of application, there are:

• quartz type glass - made by melting quartzite or rock crystal, this material It can be natural, it is formed when lightning strikes the location of quartz deposits;
• optical glass is used to make lenses or prisms;
• high resistance to impact chemical substances and temperature changes are characterized by chemical type glass;
• Industrial glass is widely used in the manufacture of various things that people use.

Industrial glass is:

• potassium-sodium type - characterized by a low melting point, it is easily obtained from different figures, has a clean and light structure;
• potassium-calcium type - has high hardness and is difficult to melt, does not have a pronounced shine;
• lead type - similar to crystal, very fragile and shiny, more expensive, heavy, but at the same time quite soft;
• borosilicate type - resistant to temperature changes, exposure to foreign substances, quite expensive.

In relation to the area of ​​use, glass is distinguished:

• window,
• containers,
• radiation resistant
• fiberglass,
• protective,
• dishes,
• crystal,
• thermometric,
• heat resistant,
• medical,
• heat resistant,
• electric bulbs,
• electrovacuum,
• optical,
• chemical,
• quartzoid.

Types of drill bits for drilling glass

The process of drilling glass requires a good, and, most importantly, suitable drill and material that will instantly cool the glass during the drilling process. Let's look at the main types of drills that are suitable for glass:

• drill in the form of a spear or feather - made of hard alloys, the diameter of such devices ranges from 3 to 12 mm, if you have the skills, drilling glass with such a drill is quite possible, but you cannot do without the formation of small chips;
• spear-shaped drills with diamond coating - characterized by softer drilling, no chips;
• tubular or round drills are used to cut circles or rings on glass surfaces; this process is most conveniently carried out using a drilling machine;
• brass glass with diamond coating requires cooling through a supply of water or turpentine;
• A tubular diamond type drill is used to drill a hole in glass, it has the form of a crown with a shank, the end of the crown is diamond coated, and requires cooling.

Preparing glass for the drilling process

1. Before you start drilling glass, you should prepare the surface for this process.

2. Using alcohol or turpentine, be sure to degrease the surface and then wipe with a dry cloth.

3. The glass sheet is not allowed to slide or shrink on the surface.

4. The glass sheet must be placed on the base.

5. It is better to mark the drilling point using construction tape or a marker.

6. If you do not have the skills to work with glass drilling, it is better to practice on small fragments so as not to ultimately spoil the material.

7. Drilling glass takes a long time; do not press hard on it to speed up the procedure.

8. Hold the drill bit at a right angle to the glass surface. Do not drill one hole at a time; stop periodically to allow the glass to cool.

9. When drilling is completed, when the hole is almost ready, you should turn the glass over and drill a hole from the back side. This procedure will help avoid chips or cracks and make the hole the desired shape.

10. To remove small roughness or unevenness on the glass surface, use fine sandpaper.

How to drill glass with a regular drill

To complete this process, you must have:

• drill, which is used for drilling metal or ceramic surfaces;
• screwdriver or low-speed drill;
• plasticine,
• turpentine,
• alcohol solution.

The glass must lie on a completely flat surface. Pay attention to the placement of the glass; the edges should not hang over and the glass should not wobble.

Install on a screwdriver or drill minimum speed rotation. Insert the glass and check whether the device breaks the glass; if there is significant runout, it is recommended to replace the drill.

Using cotton wool and alcohol, degrease the glass and make a recess out of plasticine in the place of the future hole. Pour turpentine into it and begin the drilling process. To avoid cracks, do not apply great effort, during this process. Hold the device lightly and without pressing over the glass.

The minimum rotation speed for drilling per minute is 250, and the maximum is 1000 cycles.

How to drill glass at home using sand

At a time when there were no screwdrivers and drills, this method of drilling glass was used. To drill glass using sand you will need:

• sand,
• gasoline,
• tin or lead,
• gas burner,
• metal vessel, preferably a mug.

Be sure to degrease the surface with gasoline, and pour a mound of wet sand onto the site where you intend to drill. Next, using a sharp object, you should make a funnel the size of the hole.

Pour a pre-prepared mixture of tin or lead into this form, after a few minutes, remove the sand and remove the frozen part of the glass, which should easily come off the surface.

To heat lead or tin, use a metal vessel and a gas burner. If there is no gas burner, replace it with an ordinary stove.

Such a hole is perfectly smooth and does not require additional processing effort.

How to drill glass with your own hands using a homemade drill

The drill used in the work process consists of a diamond roller, which is placed in the simplest glass cutter, and a metal rod.

You need to cut a special hole in the rod into which the diamond roller is placed. The roller is installed in such a way that it is stationary.

Attach the drill bit to a drill or screwdriver and start drilling.

This drill is a modification of conventional diamond-coated drills, so if you cannot buy such a drill, make it yourself.

Another option for making a drill involves drilling glass with a small hole diameter of up to 50 mm. Take any ordinary drill. Turn on gas burner, clamp the drill with pliers and hold it over the flame for several minutes. When the tip of the drill turns white, cool it quickly by dipping it in sealing wax. After it has cooled, remove the drill and remove drops of sealing wax from the surface, if any. This glass has become tempered and is excellent for drilling glass.

1. A little honey or turpentine should be applied to the place where the hole will be drilled in order to prevent the appearance of cracks and splits.

2. Do not press the drill from above.

3. The interval between drilling is 5-10 seconds. It is advisable to dip the drill in a vessel with water during breaks to prevent the glass from melting.

4. You cannot swing the drill from one side to the other.

5. If possible, it is better to use a screwdriver; this item is more gentle, as it has low speed.

6. The cost of drilling glass in a professional setting starts from $10, so by using these tips you can save a lot of money.

7. Not only alcohol, but also acetone is perfect for degreasing the surface.

8. When working with a drill, do not forget to follow safety precautions, wear goggles and gloves

9. The distance between the edges of fragile glass should be at least 1.5 cm, for ordinary glass 2.5 cm.

10. Best surface for working with glass - wooden.

Working with glass using a glass cutter

1. To make a hole in the glass large sizes or unusual shape, a glass cutter will do.

2. Using a felt-tip pen or marker, make a marking along which the drilling will be carried out.

3. When working with a glass cutter, you should not make sudden movements; pressure should be smooth and have the same force.

4. Using the handle of a glass cutter, tap the glass so that the cut part falls out.

5. To remove excess glass, use special tongs.

6. Pay attention to the condition of the tool before starting work. The location of the roller should be central, it should rotate smoothly and evenly.

Unconventional methods of drilling glass

1. To drill through carbide type glass, you should prepare a cooling liquid. To do this, take acetic acid and dissolve aluminum alum in it. If they are not available, mix turpentine with camphor in a one to one ratio. Treat the glass with one of the solutions, and only then start drilling.

2. If a drill is missing, use copper wire, which must be inserted into the drill. In this case, drilling occurs using a specially prepared solution. One part camphor and two parts turpentine, add coarse sandpaper type powder to this mixture. Place the mixture in the place where you want to drill a hole and start working.

3. There is another method using this solution. Use a piece of metal tubing that is inserted into the drill. Make a plasticine ring and attach it to the surface of the glass. The height of the ring is 10 mm, and the diameter is 50 mm. Apply a solution of turpentine, camphor and emery powder into the recess.

4. Take a tube made of aluminum, copper or duralumin, the length of which is about 5 cm. Drive a wooden plug into one end, and cut out the teeth with a hex file at the other end. Screw the self-tapping screw into the end on which the wooden plug is located, and saw off its head. Attach two circles pre-cut from cardboard, the diameter of which is the same as the diameter of the future hole, to the inner and outer parts of the glass. Place the glass on a rubber surface and sprinkle abrasive powder on it. Place the place where the self-tapping screw is attached, with the cut off head, in a drill or screwdriver, reverse side, treat the so-called drill with turpentine solution. Drill the third part of the hole from one side, and then turn the glass over and finish the job.

How to drill glass video:

Thanks for the useful article.

Thanks for the useful article. Helped a lot. Only we are drilling a hole, and the “hole,” excuse me, is in the ass.

Construction portal StrPort 2011-2016. Articles about repair, construction, building materials.

Copying information from the site is possible only with the permission of the editors or with a direct link to the source. Legal basis

How to make a hole in a glass bottle with your own hands

If you need to make a hole in a glass bottle, then you do not need to buy special equipment. This can be done at home with your own hands. You can drill with either a regular drill or a screwdriver.

— The bottle itself, for example, is from wine;

— Bottle stand to prevent the bottle from rolling around when drilling a hole;

— A regular drill or screwdriver;

— Water for cooling;

Let's get started

We drill in stages, in between adding a few drops of water from a syringe into the hole. This is necessary so that both the drill and the glass bottle do not overheat.

When the drill has gone through, you need to carefully drill the hole, making light rotational movements. This will make the hole cut smoother.

If you need to make a hole in a glass bottle, then you do not need to buy special equipment. This can be done at home with your own hands. You can drill with either a regular drill or a screwdriver.

It is preferable to use a screwdriver, since it has fewer revolutions (high speeds are not needed for drilling glass). It is recommended to use a drill with pobedit inserts, but if you don’t have one, you can take a regular drill for metal work, for example, in this instruction we use a drill with a diameter of 8.2 mm made of P6M5 steel. Don’t believe those who say that you only need to use pobedit drills and nothing will work with ordinary ones. Now we will make sure of this.

You can learn how to make a hole in a glass bottle by watching the video:

So, to drill a hole in a bottle you will need:
- The bottle itself, for example, from wine;
- Bottle stand to prevent the bottle from rolling around when drilling a hole;
- Paper tape;
- A regular drill or screwdriver;
- Regular drill;
- Water for cooling;
- Drill
- And a syringe.

It is necessary to secure the bottle from rotation. To do this, a stand was made in advance from ordinary wooden blocks: two long and two short, fastening them together with nails. If it is not possible to make such a stand, then you can make a small depression in the ground if you are drilling outside, or place two bricks or something else on the sides. In general, it depends on your imagination.

First thing to do- this is to wrap paper tape (several layers) around the bottle approximately where you plan to make a hole. After this, put a mark on the tape with a felt-tip pen - the center of the future hole.

The most important thing when drilling a hole is not to press too hard on the drill, as the glass may crack and the bottle will be damaged.

Let's get started
We drill in stages, in between adding a few drops of water from a syringe into the hole. This is necessary so that both the drill and the glass bottle do not overheat.

So that there are no cracks with inside bottles, you need to monitor the pressure and not overpress the drill, especially at the end of the work.
When the drill has gone through, you need to carefully drill the hole, making light rotational movements. This will make the hole cut smoother.

The hole is drilled, remove the tape and look at the result. This hole was made using a standard drill bit with a diameter of 8.2 mm and a conventional drill. It took 10-15 minutes to complete the work.